The Hong Kong University of Science and Technology · FACULTY OF ELECTRICAL ENGINEERING

ELEC1010 Chap.5 Frequency Translation and Modulation

- one subject, every graph, every model, every mark
6 Chapters4-page Bible
Our own words - no uploaded lecturer files
Updated for this semester
Chapter 5 of 10 · ELEC1010

Frequency Translation and Modulation

Preserve offsets while changing location

Baseband is the original information-bearing frequency range. Radio transmission relocates that information around a higher carrier so multiple services can occupy separate regions of spectrum and practical antennas can radiate them. In the simplified amplitude-modulation model, multiplying baseband and carrier sinusoids creates sum and difference frequencies.

Translation changes absolute location while preserving each baseband offset.

A baseband tone at fm therefore appears at fc minus fm and fc plus fm. These are the lower and upper sidebands. Convert baseband and carrier values to the same unit before adding or subtracting, then check that both answers lie close to the carrier.

Symmetry is a strong audit: the distance from the carrier to the lower line should equal the distance to the upper line.

For baseband content extending from zero to B, the ordinary two-sided translated spectrum spans from fc minus B to fc plus B. Its overall width is consequently 2B in this model. The carrier determines where the band is centred, while the baseband extent determines its width.

Moving to a different carrier changes centre frequency without stretching the information bandwidth.

Demodulation multiplies the received signal by a carrier again. That operation produces a wanted difference component at the original baseband frequency and unwanted components near twice the carrier. A low-pass filter keeps the recovered baseband and rejects the high-frequency products.

Mixing alone is incomplete because it generates both groups rather than selecting the desired one.

Receiver filtering occurs on both sides of the mixer for different reasons. A band-pass stage first selects the wanted station and rejects neighbouring carrier bands. After mixing, a low-pass stage keeps the returned baseband.

Naming these jobs separately explains how simultaneous transmissions remain separable and prevents the preselection filter from being confused with the recovery filter.

Revision is clearest with three stacked spectra: original baseband, translated transmission and recovered baseband. Use matching colours for equal offsets and annotate the carrier centre.

Solve both forward and reverse questions, stating whether a frequency is an absolute location or an offset. Finally name every rejected group; the complete chain is selection, translation, product generation and low-pass recovery.

In this chapter

What this chapter covers

  • 01

    Baseband and carrier

  • 02

    Sum and difference products

  • 03

    Lower and upper sidebands

  • 04

    Occupied bandwidth

  • 05

    Mixer recovery

  • 06

    Receiver filtering

Worked example · free

Translate a two-tone baseband

Q [10 marks]. Tones at 2 and 5 kHz modulate a 900 kHz carrier. List every sideband and the occupied span. The marks shown are an AskSia study allocation, not the University's published marking scheme.
Modulation translates frequency content around the carrier.Modulation translates frequency content around the carrier. The orange sidebands sit exactly fm below and above the blue carrier, preserving the baseband offset.A 120 kHz baseband tone translated around a 1,000 kHz carrierfc-fmfcfc+fmtranslate and preserve the offset
Modulation translates frequency content around the carrier. The orange sidebands sit exactly fm below and above the blue carrier, preserving the baseband offset.
  • 2Convert all values to kilohertz.
  • 5Calculate carrier minus and plus each tone.
  • 3Find the outer occupied edges.
The sidebands are 898 and 902 kHz for the 2 kHz tone, and 895 and 905 kHz for the 5 kHz tone. The transmitted span runs from 895 to 905 kHz, giving 10 kHz.
Sia tip — Subtract the carrier from upper lines and lower lines from the carrier; matching offsets confirm symmetry.
Glossary

Key terms

Baseband
The original information-bearing frequency range before carrier translation.
Carrier
A high-frequency signal used to relocate baseband information for transmission.
Sideband
A translated component appearing below or above the carrier.
Modulation
The process of varying a carrier so it conveys baseband information.
Demodulation
The process of recovering baseband content from a modulated signal.
FAQ

Frequency Translation and Modulation FAQ

Why are there two sidebands?

Multiplying the carrier and a baseband sinusoid creates both sum and difference frequencies. They appear equally far above and below the carrier in the simplified amplitude-modulation model.

Is carrier frequency the same as bandwidth?

No. The carrier sets the centre location of the transmitted band. The baseband extent determines how wide the translated content spreads around that centre frequency.

Why is a low-pass filter needed after mixing?

The second multiplication creates the wanted baseband difference product and unwanted components near twice the carrier. Low-pass filtering keeps the baseband and rejects those high-frequency products.

How can a sideband calculation be checked quickly?

Subtract the carrier from each upper component and subtract each lower component from the carrier. Matching offsets confirm symmetry, while the outer edges determine occupied width independently of the centre frequency.

Study strategy

Exam move

Draw three stacked spectra for each problem: original baseband, translated carrier band and recovered baseband. Use matching colours for equal offsets. Calculate sidebands in a single unit and check symmetry. For recovery questions, name the band-pass stage before mixing and the low-pass stage afterward. Audit centre, offsets and width separately.

Record the carrier centre, baseband offsets and outer occupied edges on different lines. Recompute each offset from both sides of the carrier; unequal values reveal a sign or unit error. Subtract the outer edges to obtain width rather than reporting the carrier. During recovery, trace one sideband through the mixer to both its difference and sum products, then state which filter removes each unwanted group.

This audit distinguishes ordinary two-sided amplitude modulation from any explicitly stated single-sideband system and prevents an omitted mirror component from passing merely because the remaining arithmetic looks neat.

Working through Frequency Translation and Modulation in ELEC1010? Sia is AskSia’s AI Electrical Engineering tutor — ask any ELEC1010 Frequency Translation and Modulation question and get a clear, step-by-step explanation grounded in how ELEC1010 is taught and assessed. Read this chapter free, then take your hardest questions to Sia.

A+Everything unlocked
Unlocks this Bible + all 13 of your subjects at The Hong Kong University of Science and Technology, plus 1,000+ more Bibles across the AskSia library.
Sia - your ELEC1010 tutor, unlimited, worked the way the exam marks it
The full 4-page Bible + practice bank with worked solutions
Chrome extension - sync your LMS so Sia knows your deadlines
Bilingual EN / Chinese on every Bible and every Sia answer
$0.99 Trial
30-day money-back · cancel in one tap · how it works