University of Birmingham · FACULTY OF ENGINEERING

33283 Chap.11 Building Solid Parts in Fusion 360

- one subject, every graph, every model, every mark
7 Chapters4-page Bible
Our own words - no uploaded lecturer files
Updated for this semester
Chapter 11 of 11 · 33283

Building Solid Parts in Fusion 360

Choosing how to make a body

The module's solid modelling pages stress that the same geometry can usually be built in several ways, so practise every tool and choose the most appropriate.

Extrude, revolve, sweep and loft create bodies from sketches; fillets, shells, drafts, holes, threads, mirrors and patterns finish them.

Learning from the tutorials

This chapter follows the Fusion 360 tutorials used in the module: the drafted and shelled part, the revolved coupler with its axis and angle options, the gear housing with tapped holes and cosmetic threads, and the coil feature used to cut a thread.

It shows how to check a feature with simple arithmetic before modelling it.

Checking a feature before modelling it

Several features in the tutorials can be checked with one line of arithmetic: a coil's pitch from its height and revolutions, a revolve's total angle from its two sides, a tapped hole's designation from the bolt it receives.

Doing that check first saves rebuilding a feature that was set up wrongly.

In this chapter

What this chapter covers

  • 01

    Extrude, revolve, sweep and loft

  • 02

    Shell, draft and fillet

  • 03

    Revolve axis, angle and Two Side options

  • 04

    Tapped holes from sketch points

  • 05

    Cosmetic versus modeled threads

  • 06

    Coil pitch from height and revolutions

  • 07

    Mirrors and patterns

Worked example · free

Set up a coil for a chosen pitch

Q [3 marks]. AskSia-authored practice. A 40 mm long bar needs a coil thread starting at one end, with a 4 mm pitch and 2 mm of plain bar left at the far end. What coil height and how many revolutions should you enter? The marks shown are an AskSia study weighting, not an official University allocation.
Figure 11.2.Figure 11.2. Side view of the tutorial coil drawn to scale on its 100 mm bar. Six revolutions climb 95 mm, so successive crossings on the same side are 95 divided by 6, about 15.8 mm, apart; the top 5 mm of the bar carries no thread.Pitch 15.8 mmCoil height95 mm6 revolutions
Figure 11.2. Side view of the tutorial coil drawn to scale on its 100 mm bar. Six revolutions climb 95 mm, so successive crossings on the same side are 95 divided by 6, about 15.8 mm, apart; the top 5 mm of the bar carries no thread.
  • 1Coil height = bar length minus the plain band = 40 minus 2 = 38 mm.
  • 1Revolutions = height divided by pitch = 38 divided by 4 = 9.5.
  • 1Check: 9.5 revolutions times 4 mm = 38 mm, matching the height.
Enter a height of 38 mm and 9.5 revolutions. Pitch equals height divided by revolutions, so any two of the three values fix the third.
Sia tip — Write pitch = height divided by revolutions beside the dialog and check it before clicking OK.
Glossary

Key terms

Revolve
A feature that creates a body by rotating a sketch profile about an axis.
Sweep
A feature that creates a body by moving a cross-section along a defined path.
Loft
A feature that creates a body between two or more defined sketches.
Cosmetic Thread
A thread shown as a graphic on a hole or shaft surface, usually preferred for manufacture files.
Coil Pitch
The height a coil climbs in one revolution, equal to coil height divided by revolutions.
Shell
A feature that hollows a solid body to leave a thin-walled part.
FAQ

Building Solid Parts in Fusion 360 FAQ

What is the difference between sweep and loft?

A sweep moves one cross-section along a defined path, which suits shapes such as a curved handrail. A loft builds a solid between two defined sketches, which suits transitions such as a square duct becoming round. Both create more complex geometry than an extrusion.

Should threads be modeled or cosmetic?

The holes and threads tutorial explains that modeled threads can be good for animations and renders, while cosmetic threads, a graphic applied to the surface, generally suit files intended for manufacture better. The tutorial leaves the Modeled option switched off for the gear housing.

Why would a revolve fail to create?

In the revolved coupler tutorial, selecting an axis that would make the geometry intersect itself means the revolve is not created. Choosing a different edge or axis, such as the blue Z axis, lets the profile rotate cleanly.

How do I add threaded holes at several positions at once?

In the holes and threads tutorial you first sketch a point at each hole centre and finish the sketch. The Hole command's From Sketch option then places a hole at every selected point, with the type, tap and thread designation, such as M6x1, set once for all of them.

Study strategy

Assessment move

Work the tutorials in the order the module lists them, because later lessons reuse earlier files. For each one, write a single line saying which feature built the body and why that route was chosen over another. Practise checking numbers before modelling: hole sizes against bolt designations, coil pitch against height and revolutions.

Finally, rebuild one tutorial part using a different creating feature and compare the timelines. Keep a short feature log for your design project model, noting why each feature was chosen.

Working through Building Solid Parts in Fusion 360 in 33283? Sia is AskSia’s AI Engineering tutor — ask any 33283 Building Solid Parts in Fusion 360 question and get a clear, step-by-step explanation grounded in how 33283 is taught and assessed. Read this chapter free, then take your hardest questions to Sia.

A+Everything unlocked
Unlocks this Bible + all 17 of your subjects at University of Birmingham, plus 1,000+ more Bibles across the AskSia library.
Sia - your 33283 tutor, unlimited, worked the way the exam marks it
The full 4-page Bible + practice bank with worked solutions
Chrome extension - sync your LMS so Sia knows your deadlines
Bilingual EN / Chinese on every Bible and every Sia answer
$0.99 Trial
30-day money-back · cancel in one tap · how it works