The University of Manchester · FACULTY OF ENGINEERING

AERO61021 Chap.7 Choosing and Powering Sensors

- one subject, every graph, every model, every mark
7 Chapters4-page Bible
Our own words - no uploaded lecturer files
Updated for this semester
Chapter 7 of 10 · AERO61021

Choosing and Powering Sensors

Choosing and Powering Sensors explains how an experimenter moves from a physical quantity to a device that can actually be wired, powered and read. The chapter separates transducers, which give a voltage, from transmitters, which send a current on the industrial 4 to 20 mA loop, and from digital devices that talk over a data bus.

It then treats range as a design decision: the device must exceed the expected load, including any rig or model resting on it, without being so large that the signal fills only a tiny fraction of full scale. Output form matters next. Offset voltage sensors centred on 2.5 V read negative pressures as positive voltages, while amplified load cells and thermocouples swing both ways.

Small signals need amplification, many sensors need a stable excitation supply, and ratiometric devices change their output whenever that supply drifts. The chapter closes with dynamic sensing, where piezoelectric elements suit changing loads only, and with the practical checks on packaging, mounting and supply lead time that decide whether a chosen part can be used in the lab at all.

In this chapter

What this chapter covers

  • 01

    Transducers, transmitters and digital sensors

  • 02

    Monitoring duty versus experimental duty

  • 03

    Choosing a measurement range with dead weight included

  • 04

    Offset voltage outputs and transfer lines

  • 05

    Amplification of millivolt and microvolt signals

  • 06

    Excitation, controllers and ratiometric outputs

  • 07

    Piezoresistive and piezoelectric dynamic sensing

Worked example · free

Read pressure from an offset voltage transfer line

Q [5 marks]. A differential pressure sensor spans plus and minus 500 Pa with an output from 0.5 V to 4.5 V that is linear and centred at zero pressure. Find its sensitivity and zero-pressure voltage, then convert readings of 3.3 V and 1.9 V into pressure. Marks here reflect an AskSia practice weighting, which is not an official scheme.
Applied pressure runs along the horizontal axis and output voltage up the vertical axis; the straight line passes through 2.5 V at zero pressure, so negative prApplied pressure runs along the horizontal axis and output voltage up the vertical axis; the straight line passes through 2.5 V at zero pressure, so negative pressures still give positive voltages. 0.5 V 2.5 V at 0 Pa 4.5 V −2000 Pa +2000 Pa applied pressure (Pa) output (V) 0
Applied pressure runs along the horizontal axis and output voltage up the vertical axis; the straight line passes through 2.5 V at zero pressure, so negative pressures still give positive voltages.
  • 1The output changes by 4.5 minus 0.5, which is 4.0 V, across a pressure span of 1000 Pa.
  • 1Sensitivity is 4.0 V divided by 1000 Pa, which equals 4 mV per pascal, and the midpoint voltage of 2.5 V corresponds to zero pressure.
  • 2For 3.3 V, pressure equals (3.3 minus 2.5) divided by 0.004, giving plus 200 Pa; for 1.9 V it equals (1.9 minus 2.5) divided by 0.004, giving minus 150 Pa.
  • 1Both readings sit inside the plus and minus 500 Pa range, so neither result is clipped at an end of the transfer line.
The sensor has a sensitivity of 4 mV per pascal about a 2.5 V zero, so 3.3 V means plus 200 Pa and 1.9 V means minus 150 Pa. The mark allocation shown here is AskSia practice weighting and is not a University marking scheme.
Sia tip — Subtract the zero-pressure voltage before dividing by sensitivity; dividing the raw 3.3 V by 4 mV per pascal would report 825 Pa, outside the sensor's range.
Glossary

Key terms

Transmitter
A sensor that sends its reading as a current, normally on the 4 to 20 mA industrial loop.
Excitation voltage
The supply voltage that a sensor needs in order to operate and produce its output.
Ratiometric output
A sensor output that is proportional to the supply voltage as well as to the measured quantity.
Dead weight
Load from a model, rig or fixture that the sensor carries in addition to the quantity of interest.
FAQ

Choosing and Powering Sensors FAQ

How do I pick the range of a load cell?

Estimate the largest total load first, including any rig, mounting plate or model that rests on the cell, then choose the smallest standard range that exceeds it with some margin. A much larger range keeps the device safe but spreads its full-scale uncertainty across a reading that uses only a small part of the scale.

Why do some pressure sensors output 2.5 V at zero pressure?

An offset output places zero pressure in the middle of the voltage span, so suction and overpressure both give positive voltages. That lets a single-ended acquisition input read the device without a negative supply. You recover pressure by subtracting the midpoint voltage and dividing by the sensitivity printed on the datasheet.

Why record the supply voltage during a test?

Load cells, potentiometers and many bridge sensors are ratiometric, so their output scales with excitation. If the supply sags or rises during a run, the reading changes even when the load does not. Logging the supply lets you correct the data later instead of discovering an unexplained drift after the rig has been dismantled.

Can a piezoelectric sensor measure a steady force?

No. A piezoelectric element generates charge when it is compressed, and that charge gradually leaks away, so a constant load produces an output that decays towards zero. These devices suit vibration, impact and fluctuating pressure. For a steady load choose a strain-gauge or piezoresistive device whose resistance stays changed while the load is held.

Study strategy

Assessment move

Treat sensor choice as a short design review that you can run on any measurement in the module. Start by writing the physical quantity, the expected maximum and minimum values and how fast the value changes. Then list everything that sits in the load path, because a rig, fixture or model adds to the load the device must carry.

With those numbers, pick a range that exceeds the total with modest margin and compute what fraction of full scale your signal of interest will use; if the answer is a few percent, look for a smaller device. Next, decide the output family.

A current-loop transmitter needs a current input or a conversion resistor, a voltage transducer needs a voltage range that covers both signs if the output can go negative, and a digital sensor needs code for its bus protocol. Practise converting between voltage and engineering units on offset devices by subtracting the zero voltage before dividing by sensitivity, and check that every answer lies inside the rated range.

For bridge sensors, practise the mV per V calculation in both directions: from load to output and from a measured millivolt reading back to load, with and without a change in excitation. Keep a one-page comparison of piezoresistive and piezoelectric devices so you can say at once which one can hold a static reading.

When you prepare the group project, read each datasheet for packaging, mounting, connector type and required support electronics, and note the supplier lead time, because a part that arrives after the test window has no value to the experiment. Where two candidate sensors both fit, record why you rejected the other one, since that reasoning strengthens the methods section of a report.

Last of all, rehearse explaining a sensor choice aloud in three sentences covering range, output and power, which is exactly the justification a report reader expects to see.

A+Everything unlocked
Unlocks this Bible + all 41 of your subjects at The University of Manchester, plus 1,000+ more Bibles across the AskSia library.
Sia - your AERO61021 tutor, unlimited, worked the way the exam marks it
The full 4-page Bible + practice bank with worked solutions
Chrome extension - sync your LMS so Sia knows your deadlines
Bilingual EN / Chinese on every Bible and every Sia answer
$0.99 Trial
30-day money-back · cancel in one tap · how it works