The University of Manchester · FACULTY OF ENGINEERING

AERO61021 Chap.5 Sensor Response Time and Dynamic Signals

- one subject, every graph, every model, every mark
7 Chapters3-page Bible
Our own words - no uploaded lecturer files
Updated for this semester
Chapter 5 of 10 · AERO61021

Sensor Response Time and Dynamic Signals

Sensor Response Time and Dynamic Signals deals with measurements that change while you are taking them. The chapter first separates a time-varying record into a steady mean and a fluctuating part, the DC and AC components, and shows why sampling through time is essential when an average would conceal the behaviour of interest. It then models the sensor itself.

Most transducers behave as first-order systems, so their output approaches a sudden change in input along an exponential curve controlled by one time constant. You learn to recover that time constant from a data-sheet rise time quoted at a stated percentage, and to predict how long a reading needs to settle.

The last step drives the same sensor with a sinusoid: the output is attenuated by a magnitude ratio and delayed by a phase angle, and both grow with the product of time constant and angular frequency. Working these relations with consistent units and radians gives you a quantitative way to judge whether a sensor is fast enough for the signal you intend to record, a judgement that recurs in control and filter design.

Every worked number uses original values so the method can be rehearsed independently.

In this chapter

What this chapter covers

  • 01

    Periodic, quasi-periodic and transient signals

  • 02

    Mean and fluctuating components of a signal

  • 03

    First-order exponential response to a step input

  • 04

    Recovering a time constant from a rise time

  • 05

    Magnitude ratio for a sinusoidal input

  • 06

    Phase angle and time lag between input and output

  • 07

    Links to control loops and filter design

Worked example · free

Find a time constant from a 90% rise time and test a slow oscillation

Q [6 marks]. A pressure transducer behind a long tube has a 90% rise time of 46 s. Find its time constant, state the output fraction one time constant after a step, and find the magnitude ratio for an input oscillating at 0.02 Hz. The marks shown are illustrative practice weighting and not a University marking scheme.
Time runs along the horizontal axis and output as a fraction of the step up the vertical axis; the curve reaches 63% after one time constant and 95% after 30 s,Time runs along the horizontal axis and output as a fraction of the step up the vertical axis; the curve reaches 63% after one time constant and 95% after 30 s, never quite meeting the input line.63% at τ95% at 30 sinput step010203040time (s)output / input
Time runs along the horizontal axis and output as a fraction of the step up the vertical axis; the curve reaches 63% after one time constant and 95% after 30 s, never quite meeting the input line.
  • 2Use the rearranged first-order law with zero starting output: t/τ = −ln(1 − 0.90) = ln(10) = 2.303, so τ = 46 / 2.303 = 20.0 s.
  • 1After one time constant the output reaches 1 − e^(−1), which is about 63% of the step.
  • 1Angular frequency is ω = 2π × 0.02 = 0.126 rad/s, so τω = 20.0 × 0.126 = 2.51.
  • 2The magnitude ratio is M = 1 / √(1 + 2.51²) = 1 / 2.70 = 0.37, so only about 37% of the input swing appears at the output.
The time constant is about 20 s, the output is at 63% after one time constant, and at 0.02 Hz the sensor passes only 37% of the oscillation. Marks shown are an AskSia study allocation, not an official scheme set by the University.
Sia tip — Write ω = 2πf on its own line before computing τω; using f in place of ω makes the sensor look about six times faster than it is.
Glossary

Key terms

Time constant
The time constant is the parameter of a first-order system that sets how quickly its output approaches a new input level.
Rise time
Rise time is the time a sensor takes to reach a stated percentage of a step change in its input.
Magnitude ratio
The magnitude ratio is the fraction of an input oscillation's amplitude that survives at the sensor output.
Phase lag
Phase lag is the angle by which a sensor's output oscillation trails the input oscillation.
Fluctuating component
The fluctuating component is the zero-mean part of a signal left after its steady mean is removed.
FAQ

Sensor Response Time and Dynamic Signals FAQ

Why does a slow sensor shrink an oscillating signal?

A first-order sensor is always chasing its input. When the input reverses before the output has caught up, the output turns back early and never reaches the full peak. The faster the oscillation relative to the time constant, the smaller the fraction that survives, which is what the magnitude ratio expresses through the product of time constant and angular frequency.

Does a 90% rise time equal the time constant?

No. For a first-order sensor the time constant is the time to about 63% of a step. A 90% rise time is about 2.3 time constants and a 95% figure about 3.0, so always divide by the logarithm that matches the quoted percentage before using the value in any further calculation.

What is the difference between DC and AC components?

The DC component is the steady mean of a record and the AC component is the oscillation about that mean, which averages to zero. Adding them reconstructs the original signal. Separating them helps because the mean describes the operating condition while the fluctuation carries unsteadiness, vibration or noise.

Study strategy

Assessment move

Build this chapter around one sensor and three questions: how long does it take to settle, how much of an oscillation does it pass, and how late is that oscillation. Begin by sketching a step response freehand and marking the 63% and 95% points at one and three time constants; if you can draw it from memory you can sanity-check any later answer.

Then practise the rearrangement of the first-order law until you can move between a rise time at any percentage and the time constant in one line, remembering that the logarithm term is negative and cancels the minus sign. Make a short table of percentage against multiples of τ for 50, 63, 90 and 95 percent and verify each entry yourself.

For oscillating inputs, always compute ω from f first and keep phase in radians when you divide by ω to obtain a time lag. Work the module notes' own check case, a time constant near 61 s at 0.011 Hz, and confirm you obtain a magnitude ratio of about 0.23, a lag near 77 degrees and a delay near 19 s; reproducing a known answer is the best proof your calculator is in the right mode.

Next, invent variations: halve the time constant, double the frequency, and predict the direction of change before calculating. For signals, practise decomposing a sketched periodic record into a mean and a fluctuation and explain in words what each part tells an experimenter.

In the laboratory and the group project, use these ideas to decide whether a chosen sensor can follow the phenomenon at all, and write that justification into your report rather than assuming every instrument responds instantly. As a last check, keep a one-page sheet listing the three relations for magnitude ratio, phase and time lag together with a fully worked example in your own numbers.

Reworking that sheet from a blank page each week is quicker than rereading notes and exposes slips in units or calculator mode immediately.

A+Everything unlocked
Unlocks this Bible + all 41 of your subjects at The University of Manchester, plus 1,000+ more Bibles across the AskSia library.
Sia - your AERO61021 tutor, unlimited, worked the way the exam marks it
The full 3-page Bible + practice bank with worked solutions
Chrome extension - sync your LMS so Sia knows your deadlines
Bilingual EN / Chinese on every Bible and every Sia answer
$0.99 Trial
30-day money-back · cancel in one tap · how it works