BENG0033 Chap.3 Recycle, Bypass and Process Maps
Recycle, Bypass and Process Maps
Recycle, Bypass and Process Maps handles flowsheets whose upstream conditions depend on downstream separations. Recycle returns material to an earlier operation, bypass diverts part of a stream around an operation, and purge removes material that would otherwise build up. The algebra becomes cyclic, so the process map must show mixers, splitters and the chosen tear stream clearly.
An overall boundary around the complete loop often removes the internal recycle from the first balance and establishes net feed, product and waste. Smaller unit boundaries then determine the circulation rate and compositions. A splitter preserves composition across its outlet branches unless a selective separation is specified; confusing a splitter with a separator creates false equations.
The solution order should be planned from independent specifications rather than guessed from diagram position. Closure is checked locally around units and globally around the full process, with special attention to inert accumulation and purge requirements. Recycle can raise overall recovery even when single-pass performance is unchanged, but it also increases internal flow and equipment load.
A bypass creates branches with different treatment histories that must be recombined by component. Tear-stream iteration requires convergence of composition as well as total flow. These features make the process map a calculation tool: arrow direction, junction type and percentage basis determine which equations are valid and where capacity consequences appear.
What this chapter covers
- 01
Recycle-loop process maps
- 02
Overall and unit-operation boundaries
- 03
Tear streams and solution order
- 04
Mixers, splitters and separators
- 05
Purge control of inert accumulation
- 06
Bypass specifications and closure
Worked example · free
Calculate a recycle flow
- 3Recycle is 0.80(25) = 20 kg/h and purge is 0.20(25) = 5 kg/h.
- 2Mixer feed is fresh plus recycle, 100 + 20 = 120 kg/h. Marks are original practice weighting.
Key terms
- Recycle
- Material routed from a downstream location back to an upstream operation.
- Tear stream
- A selected recycle stream temporarily treated as known to break a cyclic calculation.
- Purge
- A deliberate withdrawal from a loop that limits unwanted accumulation.
Recycle, Bypass and Process Maps FAQ
Why start with an overall balance?
The overall boundary cancels internal recycle flows, so it often reveals net feed, product and waste before the circulation rate is known. That simpler result can anchor the unit-level equations.
Does a splitter change composition?
An ideal nonselective splitter sends the same composition into each outlet and changes only the amount. A separator changes component distributions, so it needs component recovery or split specifications.
How do I choose a tear stream?
Choose a stream that breaks the loop and exposes a solvable sequence with the fewest unknown components. The choice is computational; the converged physical solution should not depend on which valid tear is selected.
What should converge in a recycle calculation?
The recalculated tear stream must match the assumed total flow and every tracked component flow. Agreement in total flow alone can conceal an incorrect recycle composition.
Exam move
Redraw every recycle question as named blocks and streams before writing equations. Use different visual symbols for a mixer, a nonselective splitter and a selective separator. First surround the entire loop with an overall boundary and write net component balances; internal recycle terms should disappear. Then select a tear stream and build a stream table that records total flow and composition at each location.
Solve units in an order supported by the available specifications, returning to the tear relation last. For purge problems, track the inert or impurity component separately because total mass alone will not reveal accumulation. Practise converting among recycle fraction, purge fraction, recycle ratio and fresh-feed basis without applying a percentage to the wrong stream.
Check every splitter with outlet fractions summing to one and every mixer with component inputs summing to its outlet. During revision, compare an algebraic simultaneous solution with one or two fixed-point iterations so the circular dependency becomes intuitive. In timed work, annotate the process map with equation numbers; this makes duplicated or dependent equations visible and leaves a clear audit trail for method marks.
Build three versions of the same flowsheet: no recycle, moderate recycle and recycle with an inert purge. Compare net recovery, mixer load and impurity concentration so the benefit and circulation penalty become visible. For a bypass case, label the branch fraction at the split and calculate compositions again after recombination; this guards against treating a bypass as selective separation.
Practise choosing two different tear streams for one small network and confirm that both give the same converged physical flows. When iterating, record guess, calculated value and residual by component, not only total flow. A total can converge while one composition remains wrong. Add capacity questions in which the fresh feed fits a unit but the mixed fresh-plus-recycle stream exceeds it.
End each answer with overall fresh feed equals net product plus purge or waste, then give the largest internal stream. This final line connects algebra to equipment sizing and prevents an apparently high overall recovery from concealing an impractical circulation load.