The University of Hong Kong · FACULTY OF ENVIRONMENTAL SCIENCE

CCST9016 Chap.1 Energy Forms, Sources and Conversion

- one subject, every graph, every model, every mark
7 Chapters5-page Bible
Our own words - no uploaded lecturer files
Updated for this semester
Chapter 1 of 7 · CCST9016

Energy Forms, Sources and Conversion

Energy is conserved, usefulness is not

Energy names the capacity to produce change, but an energy-system answer must say which form, where it crosses the boundary and what service is wanted. Chemical energy in fuel, radiant energy from the sun, kinetic energy in wind and gravitational potential energy in stored water can all become electricity or heat.

The amount is conserved through conversion, yet the ability to deliver the intended service usually declines because part of the transfer becomes dispersed heat. This is why a Sankey-style accounting should balance while an efficiency calculation stays below one.

Source, carrier and service

A primary energy source exists before deliberate human conversion.

Electricity is normally a secondary carrier: it transports energy from a generator or photovoltaic module to an appliance. A useful service is the outcome people seek, such as illumination, movement, indoor comfort or process heat. Confusing these categories produces weak comparisons. Petrol and electricity are not equivalent labels unless the comparison holds the transport service and system boundary constant.

Likewise, a household does not demand kilowatt-hours for their own sake; it demands services that require energy at particular rates and times.

Work, power and time

Work is an energy transfer caused by a force acting through a distance. Power is the rate of transfer, P = E/t, and energy follows E = Pt when power is constant. A 2 kW appliance operating for three hours uses 6 kWh, not 6 kW.

The distinction is visible in a power-time graph: height is power, width is time and area is energy. When power changes, divide the graph into shapes or integrate the curve. Always match the unit of time to the chosen energy unit.

Kilowatts times hours gives kilowatt-hours; watts times seconds gives joules.

Conversion chains and compounded loss

A chain can contain extraction, transport, conversion, transmission, storage and an end-use device. If stage efficiencies are independent ratios, total efficiency is their product.

Three stages at 80%, 90% and 75% yield 0.80 x 0.90 x 0.75 = 0.54, or 54%, not 245% and not an average of the percentages. The product reveals why improving a weak stage can matter, but the largest percentage loss is not automatically the best intervention.

Cost, duty cycle, scale and whether the rejected energy can serve another need also matter.

Boundaries make efficiency meaningful

Efficiency is useful output divided by input for a stated boundary. A motor-only efficiency excludes electricity generation; a source-to-wheel efficiency includes more of the chain. Neither is inherently wrong, but they answer different questions.

Before comparing two values, check that the useful service, time interval and included stages match. If a process supplies electricity and useful heat, say whether both outputs are counted. A number without that statement can look precise while supporting the wrong decision.

In this chapter

What this chapter covers

  • 01

    Energy forms and conservation

  • 02

    Primary sources, carriers and services

  • 03

    Work as an energy transfer

  • 04

    Power as energy per unit time

  • 05

    Energy as area under a power-time graph

  • 06

    Stage efficiency and compounded conversion loss

  • 07

    System boundaries and fair comparison

Worked example · free

Combine changing power demand with conversion efficiency

Q [8 marks]. AskSia-authored practice. A pump draws 1.8 kW for 25 minutes and then 0.9 kW for 35 minutes. The motor is 75% efficient. Find the electrical energy input and useful mechanical energy output. The marks shown are an AskSia study allocation, not the University's marking scheme.
Every energy service has a conversion chain.Every energy service has a conversion chain. The horizontal arrows show changes of form, while the downward loss arrows identify energy that leaves without providing the intended service. Follow the form, then account for the loss Primary sourcefuel, sun, wind Converted formheat or motion Carrierelectricity Useful servicelight, heat, work unused energy leaves at every conversion
Every energy service has a conversion chain. The horizontal arrows show changes of form, while the downward loss arrows identify energy that leaves without providing the intended service.
  • 3Convert both time intervals to hours and find each electrical energy rectangle.
  • 3Add the two input energies and apply motor efficiency once.
  • 2State the input and output boundaries with units.
The first interval uses 1.8 x 25/60 = 0.75 kWh. The second uses 0.9 x 35/60 = 0.525 kWh. Electrical input is therefore 1.275 kWh. Useful mechanical output is 0.75 x 1.275 = 0.95625 kWh, about 0.956 kWh. The input boundary is electricity at the motor terminals; the output is mechanical energy delivered by the motor shaft. The 0.319 kWh difference is not destroyed energy but energy leaving in non-useful forms, mainly heat for this boundary.
Sia tip — Draw one rectangle for each constant-power interval. Add energy first, then apply the efficiency that belongs to the whole motor boundary.
Glossary

Key terms

Chemical Energy
Energy associated with chemical bonds and released or absorbed during reactions.
Kinetic Energy
Energy associated with motion of an object or flowing substance.
Potential Energy
Stored energy associated with position or configuration in a force field.
Primary Source
An energy resource before conversion into a deliberately produced carrier.
Energy Carrier
A transferable form used to deliver energy between a source and service.
Useful Service
The desired outcome supplied by an energy system, such as heat, light or motion.
Work
Energy transferred when a force acts through a displacement.
Power
Energy transferred or converted per unit time.
Kilowatt-Hour
An energy unit equal to one kilowatt sustained for one hour.
Conversion Chain
The ordered stages that transform a source into a carrier and useful service.
FAQ

Energy Forms, Sources and Conversion FAQ

Why is electricity called a carrier rather than a primary source?

Electricity is usually produced by converting another form of energy, such as chemical, nuclear, gravitational, kinetic or radiant energy. It then carries energy to an end-use device. Naming the original source matters because generation losses and environmental effects differ even when the electricity delivered to the user appears identical.

When should I use joules and when should I use kilowatt-hours?

Use either energy unit as long as all quantities are consistent. Watts multiplied by seconds gives joules. Kilowatts multiplied by hours gives kilowatt-hours. Convert only when a requested answer or comparison requires it. Keeping the natural units of the data until the final step often prevents unnecessary conversion errors.

Can an efficiency ever be greater than 100%?

A genuine energy-conversion efficiency cannot exceed 100% because useful energy output cannot exceed total energy input. A heat-pump coefficient of performance can exceed one because it compares delivered heat with work input while additional heat is moved from the environment. That ratio is not the same quantity as conversion efficiency.

Why do total stage efficiencies multiply?

Each stage receives only the output surviving from the previous stage. If 80% survives first and 90% of that survives next, the result is 0.90 x 0.80 of the original input. Adding percentages treats every loss as if it acted on the same original amount, which misrepresents the chain.

Study strategy

Assessment move

Practise this chapter with three representations of the same system. First write a source-to-service sentence. Next draw boxes for conversions and arrows for useful output and loss. Finally add a small table of power, time, energy and efficiency with units. Change one number and predict the direction of the answer before calculating.

For power-time questions, sketch the graph and label its area as energy; for a variable profile, split it into rectangles or triangles. For chain questions, write every efficiency as a decimal on its arrow and multiply only the stages inside the stated boundary. Then perform two checks.

The energy balance should account for input as useful output plus losses, and the total efficiency should not exceed the efficiency of the weakest included stage. When comparing technologies, rewrite both around the same service rather than the same carrier. A useful final drill is to explain why a correct device efficiency can still support a poor system decision.

If your answer does not name the boundary, add it before adding more arithmetic.

A+Everything unlocked
Unlocks this Bible + all 52 of your subjects at The University of Hong Kong, plus 1,000+ more Bibles across the AskSia library.
Sia - your CCST9016 tutor, unlimited, worked the way the exam marks it
The full 5-page Bible + practice bank with worked solutions
Chrome extension - sync your LMS so Sia knows your deadlines
Bilingual EN / Chinese on every Bible and every Sia answer
$0.99 Trial
30-day money-back · cancel in one tap · how it works