The University of Hong Kong · FACULTY OF ENGINEERING

ENGG1000 Chap.5 Force Vectors and Cartesian Components

- one subject, every graph, every model, every mark
7 Chapters3-page Bible
Our own words - no uploaded lecturer files
Updated for this semester
Chapter 5 of 10 · ENGG1000

Force Vectors and Cartesian Components

Magnitude and direction travel together

Force is a vector, so adding force magnitudes without directions is valid only for collinear signed quantities. Head-to-tail geometry and Cartesian components express the same addition.

Components are usually more reliable because each axis can be summed independently.

Coordinates define a line of action

A cable direction from A to B comes from the position vector B minus A. Dividing by its magnitude produces a unit vector, and multiplying by the tension produces the force vector.

Direction cosines are the unit-vector components and their squares sum to one.

Establish axes before resolving anything

Draw the positive coordinate directions and state how each angle is measured. A component is the projection of the vector onto an axis, so the correct sine or cosine follows from geometry rather than a memorised horizontal rule. Carry component signs from the sketch.

If a vector points left or down, the corresponding Cartesian component is negative even though the vector magnitude remains positive.

Use a unit vector for coordinate-defined forces

Subtract the tail coordinates from the head coordinates to obtain the direction vector. Divide that vector by its length, verify that the resulting components have squared sum one, and only then multiply by the force magnitude.

Reversing the subtraction produces the opposite force direction, so labels such as force on A directed toward B should be translated into an explicit tail-to-head statement before calculation.

Add vectors component by component

Resolve every force into the same basis, sum all x components, all y components and, when needed, all z components, then reconstruct the resultant.

Its magnitude must be nonnegative, while its direction should be reported with an unambiguous quadrant or unit vector.

A quick bound checks that the resultant magnitude cannot exceed the sum of individual magnitudes, and complete cancellation is possible only when directions permit a closed vector polygon.

Separate a force from its line of action

Two equal component vectors applied at different locations have the same translational resultant but may not have the same rotational effect.

Force-vector calculations establish magnitude and direction; moment calculations additionally require position relative to a reference point. Preserving that distinction prepares the transition to statics and prevents coordinates describing a point of application from being confused with coordinates describing force direction.

In this chapter

What this chapter covers

  • 01

    Scalars and vectors

  • 02

    Head-to-tail addition

  • 03

    Cartesian components

  • 04

    Unit vectors

  • 05

    Position vectors

  • 06

    Direction angles

  • 07

    Three-dimensional resultants

Worked example · free

Turn endpoints into a cable force

Q [8 marks]. AskSia-authored practice. A 520 N cable runs from A(1, 1, 0) to B(4, 5, 12) metres. Find the force from A toward B. The marks shown are an AskSia study allocation, not the University's marking scheme.
The orange force and its blue and purple components are equivalent.The orange force and its blue and purple components are equivalent. The coordinates are derived from the stated angle, so recombining the orthogonal components recovers the same magnitude and direction.One force, two orthogonal components, one unchanged resultantFx = F cos θFyFθ
The orange force and its blue and purple components are equivalent. The coordinates are derived from the stated angle, so recombining the orthogonal components recovers the same magnitude and direction.
  • 3Form the directed position vector.
  • 2Normalise it.
  • 3Multiply and check magnitude.
The position vector is 3i + 4j + 12k metres and has magnitude 13 metres. The unit vector is therefore 3/13 i + 4/13 j + 12/13 k. Multiplying by 520 N gives 120i + 160j + 480k N. Its magnitude is 520 N, confirming the components.
Sia tip — Subtract coordinates in the force direction and reject any unit vector whose magnitude is not one.
Glossary

Key terms

Vector
A quantity carrying magnitude and direction.
Resultant
The single vector equivalent to a vector system's sum.
Component
The signed projection of a vector along an axis.
Unit Vector
A dimensionless direction vector of magnitude one.
Position Vector
A directed displacement between two points.
Direction Cosine
The cosine of the angle between a vector and a coordinate axis.
FAQ

Force Vectors and Cartesian Components FAQ

Why can I not add force magnitudes directly?

Forces with different directions do not act along one scalar line. Resolve them into signed components or use head-to-tail geometry, then add vectorially. Direct magnitude addition discards the directional information that determines the physical resultant.

Which coordinate subtraction order should I use?

If the force points from A toward B, form the position vector as coordinates of B minus coordinates of A. Reversing the subtraction preserves magnitude but reverses every component, producing a force in the opposite physical direction.

How should I report a vector direction?

Give signed Cartesian components, direction angles or a magnitude with an unambiguous angle and quadrant. Inspect component signs after using inverse tangent, because a calculator may return a reference angle without identifying the correct quadrant.

Study strategy

Exam move

Sketch axes and the vector before selecting sine or cosine. Practise endpoint problems until the subtraction order, normalisation and magnitude check become automatic. For resultants, resolve every force independently, sum components, reconstruct magnitude and use the sketch to verify the quadrant of the final direction.

Keep a fixed solution layout with one row per force and columns for x, y and z components; the final row is the resultant. For coordinate-defined cables, write tail, head, difference, length and unit vector on separate lines so reversal errors are easy to locate. Check every unit vector independently before multiplying by magnitude.

End by estimating the resultant direction from the drawing and applying the triangle-inequality bound to its magnitude before accepting the calculator output.

A+Everything unlocked
Unlocks this Bible + all 52 of your subjects at The University of Hong Kong, plus 1,000+ more Bibles across the AskSia library.
Sia - your ENGG1000 tutor, unlimited, worked the way the exam marks it
The full 3-page Bible + practice bank with worked solutions
Chrome extension - sync your LMS so Sia knows your deadlines
Bilingual EN / Chinese on every Bible and every Sia answer
$0.99 Trial
30-day money-back · cancel in one tap · how it works