The University of Hong Kong · FACULTY OF ENGINEERING

ENGG1000 Chap.3 Semiconductors, Junctions and Microelectronics

- one subject, every graph, every model, every mark
7 Chapters3-page Bible
Our own words - no uploaded lecturer files
Updated for this semester
Chapter 3 of 10 · ENGG1000

Semiconductors, Junctions and Microelectronics

Controllable conduction

Semiconductors have a bandgap small enough for thermal, optical or electrical energy to create mobile carriers.

Doping changes the carrier population: electrons dominate n-type material and holes dominate p-type material, while the bulk material remains approximately neutral.

The junction is directional

Joining p-type and n-type regions creates a depletion region and an internal barrier.

Forward bias reduces the effective barrier and permits substantial current; reverse bias increases it and suppresses current before breakdown.

Device calculations must name the chosen diode model because ideal, constant-drop and full-characteristic models are not interchangeable.

Distinguish carriers from net material charge

N-type and p-type labels identify majority mobile carriers, not permanently negative and positive blocks of material.

Donor or acceptor atoms alter the carrier population while ionised dopants and mobile carriers preserve approximate bulk neutrality away from the junction.

This distinction matters when explaining current: conventional current follows positive-charge direction, electron motion is opposite, and a hole describes the useful absence of an electron rather than a separate fundamental particle.

Read bias from terminal polarity

Before deciding whether a diode conducts, mark the p-side, n-side and applied polarities.

Forward bias lowers the junction barrier and narrows the depletion region; reverse bias raises the barrier and widens it. The verbal rule should accompany the circuit sign convention so a rotated symbol does not reverse the reasoning.

After choosing the state, check that the calculated current direction and terminal voltage agree with that assumed state.

Name the device model before calculating

An ideal diode becomes a short circuit when on and an open circuit when off. A constant-drop model assigns a stated forward voltage, while a characteristic-curve model relates current and voltage nonlinearly.

Each is an approximation at a different level of detail. Solve under one declared model, then verify its consistency; an assumed conducting state that produces reverse current means the circuit must be re-analysed under the off state.

Connect microscopic control to circuit function

Junction behaviour supports rectification because opposite polarities produce very different currents.

Transistors extend controllable conduction so a smaller input can regulate a larger path, enabling amplification and switching. Integrated circuits place many such devices and interconnections on one substrate. The useful reasoning chain runs from carrier population to junction barrier, from barrier to terminal behaviour, and from terminal behaviour to the logic or analogue function of the larger circuit.

In this chapter

What this chapter covers

  • 01

    Valence and conduction bands

  • 02

    Bandgap energy

  • 03

    Electron and hole carriers

  • 04

    Donor and acceptor doping

  • 05

    Depletion region

  • 06

    Forward and reverse bias

  • 07

    Diode circuit models

Worked example · free

Use a constant-drop diode model

Q [6 marks]. AskSia-authored practice. A 6 V source drives a forward-biased silicon diode and 1.5 kilo-ohm resistor in series. Use a 0.7 V drop. The marks shown are an AskSia study allocation, not the University's marking scheme.
Two energy pictures explain one device.Two energy pictures explain one device. The left side shows excitation across a bandgap, while the right side shows how joining p-type and n-type regions creates a barrier that applied bias can raise or lower.Bandgap controls carriers; bias controls the junction barrierconduction bandvalence bandEgp-typen-typeforward bias narrows barrier
Two energy pictures explain one device. The left side shows excitation across a bandgap, while the right side shows how joining p-type and n-type regions creates a barrier that applied bias can raise or lower.
  • 2Assign the diode drop.
  • 2Find resistor voltage and current.
  • 2State the model limitation.
The resistor voltage is 6.0 minus 0.7, or 5.3 V. Current is 5.3/1500 = 0.00353 A, which is 3.53 mA. The result is valid under the stated constant-drop model; a real diode's voltage changes with current and temperature.
Sia tip — Decide the bias first, then replace the diode with one stated model and keep that model throughout.
Glossary

Key terms

Bandgap
The forbidden energy interval between valence and conduction bands.
Electron Carrier
A mobile negative carrier contributing to semiconductor current.
Hole Carrier
An empty electronic state that behaves as a mobile positive carrier.
Doping
Intentional addition of impurities to control carrier populations.
Depletion Region
The carrier-poor junction zone containing fixed ionised dopants.
Forward Bias
Applied polarity that reduces the junction barrier.
FAQ

Semiconductors, Junctions and Microelectronics FAQ

Is p-type material positively charged?

No. The p label identifies holes as the majority mobile carriers. Fixed ionised dopants balance charge in the bulk, so the crystal remains approximately neutral even though its transport behaviour is dominated by hole motion.

Why does a diode conduct mainly one way?

Its PN junction has a built-in depletion barrier. Forward bias reduces the effective barrier and allows majority carriers to cross, while reverse bias increases the barrier and leaves only small leakage before breakdown.

Why must I state the diode model?

An ideal diode, a constant-drop diode and a full current-voltage characteristic make different approximations. Naming the model tells the reader why a voltage was fixed or current was treated as zero and defines the precision of the result.

Study strategy

Exam move

Use a three-column page headed material, bias and circuit consequence. For every statement, decide which column it belongs in before connecting it to the next. Redraw the bandgap and junction barrier from memory, then solve simple series circuits under two different diode models to see exactly where the answers diverge.

Add a consistency loop to each diode solution: assume a state, replace the device by that model, solve the surrounding circuit, and compare the resulting polarity and current with the assumption. Practise explaining n-type and p-type material without calling the bulk material charged. Then trace one device function at three scales, moving from carriers to junction behaviour to the larger switching or rectifying role.

This prevents a correct circuit rule from becoming disconnected from its physical cause.

A+Everything unlocked
Unlocks this Bible + all 52 of your subjects at The University of Hong Kong, plus 1,000+ more Bibles across the AskSia library.
Sia - your ENGG1000 tutor, unlimited, worked the way the exam marks it
The full 3-page Bible + practice bank with worked solutions
Chrome extension - sync your LMS so Sia knows your deadlines
Bilingual EN / Chinese on every Bible and every Sia answer
$0.99 Trial
30-day money-back · cancel in one tap · how it works