ELEC1010 Chap.1 Signals and System Representations
Signals and System Representations
Read the independent variable first
A signal is a variation that carries information, so the first question is not whether a graph looks continuous or complicated. Ask what quantity varies and what coordinate organises the variation. A microphone voltage varies through time, a grey-scale image varies across two spatial coordinates, and a video varies across space and time.
Naming that independent variable prevents a time trace, image and sequence of frames from being treated as interchangeable pictures.
The dependent value needs equal care. Voltage, acoustic pressure, temperature and pixel brightness can all act as signal values, but their units and interpretation differ. A labelled axis supplies evidence that an unlabelled curve does not.
When comparing examples, write the independent variable, dependent quantity and unit in separate columns. This simple inventory exposes distractors that classify a signal only by how smooth or jagged its drawing appears.
Analog and digital describe permitted value sets, not whether the underlying physical phenomenon is natural or electronic. An analog signal can take values throughout a continuous range.
A digital representation selects from a finite alphabet, often binary words. Sampling makes the independent time coordinate discrete, while quantization restricts amplitude values. A sequence may involve either operation or both, so the words sampled and quantized should not be used as synonyms.
A system maps an input signal into an output signal.
In a sensor-controller-actuator chain, the sensor converts a physical variable to an electrical representation, the controller applies a rule, and the actuator converts the command into a physical effect. Draw alternating signal and system nodes rather than a list of device names.
The alternation makes it clear which object carries information and which object performs a transformation.
System descriptions should name the operation at the appropriate level. A rounding block quantizes values; a threshold block compares with a limit; a filter changes frequency components; a display maps stored numbers to visible intensity.
Calling every block processing hides the mechanism that a question is testing. Trace one supplied value through the chain and confirm that the output unit matches the stated physical or digital quantity.
For revision, take one familiar product and redraw it three ways: as a physical chain, as alternating signals and systems, and as analog or digital representations.
Then change one link and state what conversion becomes necessary. The exercise links vocabulary to a causal map and makes later chapters easier, because filters, samplers, quantizers, encoders and channels can all be inserted as named systems in the same framework.
What this chapter covers
- 01
Signals over time and space
- 02
Analog and digital restrictions
- 03
Sampling versus quantization
- 04
Input and output mappings
- 05
Subsystem information chains
- 06
Conversion losses
Worked example · free
Separate signals from systems
- 3Name each varying quantity.
- 3Name each input to output mapping.
- 2State where approximation enters.
Key terms
- Signal
- A pattern or variation carrying information.
- Analog Signal
- A signal varying continuously in time and value.
- Digital Signal
- A signal defined at discrete instants with values from a finite set.
- System
- An arrangement or rule mapping an input signal to an output signal.
- Subsystem
- A component system inside a larger input and output chain.
Signals and System Representations FAQ
Can a picture be a signal?
Yes. Pixel brightness varies over two spatial coordinates, so an image is a spatial signal. A video adds time because the image changes from frame to frame.
Does sampling alone make a signal digital?
Sampling makes time discrete, but a stored digital representation also needs a finite set of allowed values. Quantization supplies that value restriction and introduces a separate approximation.
Can one device be both input and output?
A device is treated as a system, while the quantities entering and leaving it are signals. Its output can become the input signal to the next subsystem in the chain.
What should be labelled on a system diagram?
Label each signal with its quantity, independent variable and unit, and label each system with the operation it performs. The alternating structure then shows exactly where representation or conversion changes occur.
Exam move
Choose a familiar device and draw alternating signal and system nodes. Label the independent variable and unit on every signal, then circle the operation performed at each system. Redraw the chain after replacing one analog link with a digital representation and name whether sampling, quantization or both are required. Audit every classification by naming the observable feature that supports it.
A time signal needs a time coordinate, a spatial signal needs position, a digital value needs a finite alphabet, and a system needs an input-output mapping. Then state what the label does not imply: digital does not mean error-free, analog does not mean acoustic, and a system need not be a physical box.
Finish with one mixed chain, such as a camera that samples a spatial field, quantizes brightness, stores binary words and later drives a display. Assign each description to its stage so several true labels are not mistaken for a contradiction.
Working through Signals and System Representations in ELEC1010? Sia is AskSia’s AI Electrical Engineering tutor — ask any ELEC1010 Signals and System Representations question and get a clear, step-by-step explanation grounded in how ELEC1010 is taught and assessed. Read this chapter free, then take your hardest questions to Sia.