The Hong Kong University of Science and Technology · FACULTY OF ENGINEERING

MCEE6000D Chap.10 Copper Nanoparticle Paste for Printed Electronics

- one subject, every graph, every model, every mark
7 Chapters4-page Bible
Our own words - no uploaded lecturer files
Updated for this semester
Chapter 10 of 11 · MCEE6000D

Copper Nanoparticle Paste for Printed Electronics

A synthesis built for a market

Copper nanoparticles cost far less than silver and conduct well, so they are replacing silver in some printed electronics. Copper oxidises readily in air, though, and most liquid-phase syntheses run below 0.2 M with poor size control and tedious separation.

The published study by the course instructor and a colleague reports a route at up to 1 M copper with sizes tunable from about 12 to 99 nm and a modifiable particle surface.

How it works and how it performs

Copper acetate supplies the metal, ammonia forms a soluble complex, sodium hydroxide converts part of the copper into poorly soluble hydroxide, and hydrazine reduces both.

Fast reduction of the complex gives small particles and slow reduction of the hydroxide gives large ones, so the sodium hydroxide dose sets the mean size. Capping with fatty acids, thiols or polymers protects the surface and decides whether particles disperse in solvents or water. A gram-scale run recovered 95 to 96 per cent of the copper.

Formulated into a 75 wt% paste, screen printed on PET and sintered at 120 degrees C, the film reached a resistivity of about 5.87 times 10 to the minus 5 ohm centimetre and survived repeated bending at large radii.

In this chapter

What this chapter covers

  • 01

    Why copper is replacing silver

  • 02

    Limits of earlier synthesis routes

  • 03

    Reagent roles in the one-pot synthesis

  • 04

    Sodium hydroxide as the size lever

  • 05

    Capping agents and dispersion

  • 06

    Scale-up and characterisation

  • 07

    Paste, sintering, resistivity and bending

Worked example · free

Pick the sodium hydroxide level for a 60 nm target

Q [3 marks]. AskSia-authored practice. A customer wants particles of about 60 nm with polydispersity under 20 per cent. From the published series, 1.5 M sodium hydroxide gave 55.5 nm with a standard deviation of 13.9 nm, and 1.8 M gave 62.0 nm with 12.0 nm. Which level meets both requirements? The marks shown are an AskSia study allocation, not a University marking scheme.
Particle size set by sodium hydroxide.Particle size set by sodium hydroxide. Each dot is a published mean diameter with a bar of one standard deviation; raising sodium hydroxide from 0 to 2.5 M raises the mean from 12.0 to 98.9 nm and widens the spread.NaOH (M)Diameter (nm)01.02.05010015012.0 nm98.9 nm
Particle size set by sodium hydroxide. Each dot is a published mean diameter with a bar of one standard deviation; raising sodium hydroxide from 0 to 2.5 M raises the mean from 12.0 to 98.9 nm and widens the spread.
  • +1Polydispersity at 1.5 M: 13.9 divided by 55.5, times 100, is 25.0 per cent, which fails.
  • +1Polydispersity at 1.8 M: 12.0 divided by 62.0, times 100, is 19.4 per cent, which passes.
  • +1Both means are near 60 nm, so the spread decides: choose 1.8 M.
Use 1.8 M sodium hydroxide. It gives a 62.0 nm mean at 19.4 per cent polydispersity, while 1.5 M is close in size but too broad at 25 per cent.
Sia tip — Compute polydispersity as standard deviation over mean before comparing; two batches with similar means can differ sharply in spread.
Glossary

Key terms

Capping Agent
A molecule that coats a nanoparticle surface to prevent oxidation and self-sintering.
Polydispersity
The standard deviation of particle diameter divided by the mean, expressed as a percentage.
Sheet Resistance
The resistance of a thin film per square, which times thickness gives volume resistivity.
Sintering
Joining particles into a continuous conductor by heating, possible at lower temperature for nanoparticles.
Tetraamminecopper Complex
The soluble copper-ammonia ion whose fast reduction gives very small particles.
Screen Printing
Pressing a paste through a patterned mesh onto a substrate to form printed tracks.
FAQ

Copper Nanoparticle Paste for Printed Electronics FAQ

Why does more sodium hydroxide give bigger copper particles?

Sodium hydroxide converts part of the copper into copper hydroxide, which is extremely insoluble. Reduced on its own, the soluble copper-ammonia complex nucleates fast and gives particles of about 5 nm, while the hydroxide nucleates slowly and grows for longer, giving particles as large as 500 nm. More hydroxide shifts the mix towards larger particles.

How was the paste's conductivity measured?

Sheet resistance was measured with a four-point probe and film thickness with an optical profiler, each repeated, and volume resistivity was calculated as sheet resistance times thickness. For films sintered at 120 degrees C the paper reports about 5.87 times 10 to the minus 5 ohm centimetre.

Why was nonanoic acid used to coat the particles for the paste?

Both the thiol and the nonanoic acid coatings kept the particles free of copper oxide after a month in air, but the nonanoic acid coating carries no sulfur. The sulfur-free particles were therefore chosen as fillers for the screen-printing paste.

How well did the printed copper tracks survive bending?

At a 40 mm bend radius the resistance did not change over 1,000 cycles. At 20 mm it rose about 6 per cent by 500 cycles and then stayed flat to 1,000. At 10 mm it rose 2 per cent within 10 cycles and kept climbing to 1.67 times the starting value after 1,000 cycles.

Study strategy

Exam move

Learn the reagent roles as a five-line list, then explain the size mechanism in three sentences without notes. Practise the polydispersity and resistivity calculations, and memorise what happened at each bending radius. Rank the three bending radii by damage and say what that implies for a foldable product.

Working through Copper Nanoparticle Paste for Printed Electronics in MCEE6000D? Sia is AskSia’s AI Engineering tutor — ask any MCEE6000D Copper Nanoparticle Paste for Printed Electronics question and get a clear, step-by-step explanation grounded in how MCEE6000D is taught and assessed. Read this chapter free, then take your hardest questions to Sia.

A+Everything unlocked
Unlocks this Bible + all 13 of your subjects at The Hong Kong University of Science and Technology, plus 1,000+ more Bibles across the AskSia library.
Sia - your MCEE6000D tutor, unlimited, worked the way the exam marks it
The full 4-page Bible + practice bank with worked solutions
Chrome extension - sync your LMS so Sia knows your deadlines
Bilingual EN / Chinese on every Bible and every Sia answer
$0.99 Trial
30-day money-back · cancel in one tap · how it works