The Hong Kong University of Science and Technology · FACULTY OF ENGINEERING

MCEE6000D Entrepreneurship of Materials Technologies

- one subject, every graph, every model, every mark
11 Chapters49-page Bible
Our own words - no uploaded lecturer files
Updated for this semester
The Complete Exam Bible · Fall 2026-27

MCEE6000D Overview

Entrepreneurship of Materials Technologies
— Learn the materials science, then use it to design a product and a startup plan around it.
  • HKUST
  • Fall 2026-27
  • Postgraduate course
  • Engineering
  • Closed-book final exam
  • Co-listed with MATE 5005

What this course asks you to do

Entrepreneurship of Materials Technologies, co-listed as MATE 5005, is a postgraduate course taught from the Department of Chemical and Biological Engineering.

  • Assessed by A closed-book final exam, a team design project that ends in a business plan and pitch deck, and homework.
  • Hardest step Long calculations that need the yield or tolerance check before the formula, with units carried through.
  • How to prepare Memorise definitions and thresholds for the recall sections, and redo the homework-type selection problems.
  • Where to confirm Assignment weights, deadlines and presentation dates are kept current on Canvas.
MCEE6000D · The Hong Kong University of Science and Technology
An independent, AskSia-authored study guide. AskSia is not affiliated with, endorsed by, or sponsored by The Hong Kong University of Science and Technology; the course code and name are used for identification only.
Assessment

How MCEE6000D is assessed

ComponentWeightFormat
Homework5%E-submitted to Canvas on the due date; to be solved without AI tools
Final exam45%Closed book: multiple-choice, fill-in-the-blanks, short and long questions; equations provided for the long questions
Design project: Technical idea & manufacturing15%Team project, part of the 50% design project
Design project: Market study, financial & organization15%Team project, part of the 50% design project
Design project: Business plan (writeup)10%Word file of at most 15 pages, appendices excluded
Design project: Presentation (PPT and writeup)10%Pitch deck of at most 10 body slides, presented as a narrated video with questions

The course plan lists these weights and they total 100%: homework 5%, final exam 45% and a design project of 50% split into four parts. The plan's schedule names five numbered assignments with due dates while the grading table carries one homework line, and the schedule is described as subject to adjustment, so check on Canvas how each assignment counts. The project announcement gives pitch deck presentations on 21 and 28 November in its timeline and on 21 and 30 November on another slide; confirm the second date on Canvas.

Assessment structure

45%15%15%10%10%Homework 5%Final examDesign project, four parts

Segment widths reproduce the published weights: homework 5%, final exam 45% and the design project 50% in four parts, totalling 100%.

Current dates · verify in LMS

Current MCEE6000D dates

DateItemControl
19 September 2026Homework 1Due date printed on the homework sheet and in the course plan schedule.
15 October 2026Elevator pitch reportSingle slide file with at most four body slides, discussed in class on 17 October.
19 November 2026Pitch deckAt most ten body slides; decks are posted on Canvas around 20 or 21 November.
21 and 28 November 2026Pitch deck presentationsTimeline and course plan dates; another slide of the announcement gives 21 and 30 November.
30 November 2026Written business planWord file of at most 15 pages, appendices excluded.

Dates are as published in the course plan schedule, the homework sheet and the term project announcement for this offering. Confirm exact deadlines and submission settings in the live LMS.

Contents · every chapter, one map

What MCEE6000D covers

Eleven chapters follow the opening modules of the course plan, from material products and supply chains through materials properties and product design methods to two case studies and the business plan.

01

Material Products and Entrepreneurship

the definition of entrepreneurship · the five-stage venture process · startup against intrapreneurship · why engineers found companies

Why a materials course starts with companies

The opening module argues that innovation in material products drives technological and economic development, and it names the products that prove it: carbon fibre composites in aircraft, lithium batteries behind electric vehicles, solar photovoltaics, wearables, optical fibre and smartphones.

  • Material products that reshaped industries
  • Entrepreneurship defined in four working parts
  • Economic, technological and social roles of founders
  • The five stages from idea to growth
  • Startup against established company
  • Intrapreneurship cases from Google to Huawei
02

Chemical and Material Supply Chains

primary sources of chemicals · B2B and B2C products · ammonia, polyester and chlor-alkali routes · material classes and the materials business

From four sources to the shelf

Every chemical and material traces back to minerals, to oil and natural gas, to the air and water around us, or to living things.

  • Four primary sources of chemicals and materials
  • Hydrogen, ammonia and urea routes
  • Ethylene derivatives and polyester
  • B2B against B2C products
  • Chemicals against materials
  • Five material classes and their properties
03

Mechanical Properties of Metals

stress and strain · Hooke's law and Poisson's ratio · yield by the offset method · ductility, hardness, fatigue and creep

Reading a tensile test

Stress is load over original area and strain is change in length over original length.

  • Stress, strain and Hooke's law
  • Poisson's ratio and lateral contraction
  • Yield by the 0.002 offset
  • Tensile strength, necking and fracture
  • Selecting an alloy against two limits
  • Ductility and the brittleness threshold
04

Electrical Properties and Semiconductors

Ohm's law, resistivity and conductivity · energy bands · electron and hole mobility · n-type and p-type doping

Conduction from the outside in

Ohm's law ties current to voltage through resistance, and resistance splits into a material property, resistivity, and the specimen's length and area. Conductivity is the reciprocal of resistivity.

  • Ohm's law, resistivity and conductivity
  • Band structures of conductors, insulators and semiconductors
  • Intrinsic semiconduction in silicon and germanium
  • Electron and hole mobility
  • Sizing a wire against a voltage drop
  • Donor and acceptor doping
05

Crystal Structure, Ceramics and Polymers

crystals, grains and point defects · dislocations and strengthening · shape memory alloys · glass, ceramics and polymer crystallinity

Order, defects and strength

Most metals are crystalline and polycrystalline, built of grains that nucleated at different places.

  • Crystals, polymorphism and grains
  • Vacancies, interstitials and solid solutions
  • Dislocations and three strengthening routes
  • The Hall-Petch relation
  • Shape memory in nitinol
  • Glass, glass-ceramics and clay products
06

Hierarchical Product Design Framework

product, process, business and management decisions · phases and job functions · objective-time charts and RAT2IO · Stage-Gate and TRL

Four decisions in one framework

Developing a materials product means deciding what to make, how to make it, whether to make it and how to do it efficiently: product, process, business and management decisions.

  • Product, process, business and management decisions
  • Three phases against five job functions
  • Objective-time charts
  • The RAT2IO mnemonic
  • Stage-Gate reviews and their outcomes
  • Technology Readiness Levels 1 to 9
07

Functional Products and Devices

functional products and their functions · glass strengthening and heat sinks · controlled-release granules · dehumidifiers and the electrolyser

Products by function

Module 5 defines a functional product by what it does and a device as one that takes material in and sends material out.

  • Functional products and their functions
  • Conductive ink, cover glass and heat sinks
  • Transparent solar windows and die attach adhesive
  • Thin glass in foldable phones
  • Release profiles for controlled-release granules
  • Compressor and desiccant dehumidifiers
08

Ideation and the Five-Step Design Procedure

ideation methods and idea sources · the five design steps · materials and structure selection · AI tools in the design project

Finding an idea

Module 6a gives four ideation methods: identify unmet needs, improve existing products, analyse value chains, and explore scientific discoveries, each with an example, from a wearable reporting blood pressure and glucose to a nitinol cooler built by HKUST engineers.

  • Four ideation methods
  • Sources of product ideas
  • AI prompts for pitch decks and process plans
  • Specifying utility and sensorial functions
  • Phenomena, parameters and property constraints
  • Ingredients and three levels of structure
09

Transdermal Patch Design for a Herbal Tincture

customer needs and quality factors · matrix against reservoir patches · compatibility and diffusion tests · prototype and continuous process

The product problem

A popular herbal tincture for muscle pain is applied by pouring liquid onto gauze, which customers found hard to measure, wasteful, irritating to the skin because of the alcohol, and too uncomfortable to keep on for the advised time.

  • Customer complaints about the tincture
  • Quality factors, specifications and tests
  • Matrix against reservoir patches
  • Compatibility tests on patch materials
  • Diffusion tests on membranes and gels
  • The selected materials
10

Copper Nanoparticle Paste for Printed Electronics

copper against silver · reagent roles and size control · passivation and scale-up · paste resistivity and bending tests

A synthesis built for a market

Copper nanoparticles cost far less than silver and conduct well, so they are replacing silver in some printed electronics.

  • Why copper is replacing silver
  • Limits of earlier synthesis routes
  • Reagent roles in the one-pot synthesis
  • Sodium hydroxide as the size lever
  • Capping agents and dispersion
  • Scale-up and characterisation
11

Business Plan, Pitch Deck and Term Project

business plan components · pitch deck and elevator pitch · project tasks, teams and deadlines · how the project is graded

Where the course ends up

The design project, worth half the grade, asks teams of four to turn a materials-based product into a startup plan.

  • Four project tasks and their leaders
  • Baseline projects and choosing your own
  • The elevator pitch report
  • The pitch deck narrative
  • Business plan components
  • Deadlines from September to November

Its stated objective is that students combine science with business thinking to plan, start and run a company that sells a new materials-based product. The course plan describes three strands running together: materials science and engineering, finance and business, and current affairs.

Learning outcomes range from mastering the physics and chemistry of key materials and explaining how materials-based products work, through designing manufacturing processes, to producing a professional business plan and pitch deck while using AI tools under principle-based judgement.

How the assessment is built

The letter grade comes from homework, a closed-book final exam and a team design project.

The final contains multiple-choice, fill-in-the-blank, short and long questions; the recall sections depend on remembered concepts, and relevant lecture equations are provided for the long questions.

The design project is graded in four parts, from the technical idea and manufacturing plan to the presentation, and a small number of exam questions are set on the student projects themselves.

What the chapters cover

The guide follows the opening modules of the course plan.

It begins with material products and the entrepreneurship process, then traces chemicals and materials from four primary sources to consumer goods. Three chapters cover materials properties with homework-type calculations: stress, strain and yield in metals; conduction, band gaps and doping; and crystal structure, glass, strengthening and polymer diffusion.

The design chapters set out the hierarchical framework with Stage-Gate and Technology Readiness Levels, a catalogue of functional products and devices, and the five-step design procedure. Two published case studies by the course instructor, a herbal transdermal patch and a copper nanoparticle paste, show the whole method on real products, and the last chapter covers the business plan, pitch formats and project deadlines.

Worked example · free

Read a yield strength by the offset rule and judge a load

Q [4 marks]. AskSia-authored practice. A tensile curve for a new alloy is linear with modulus 100 GPa up to about 240 MPa and then bends over. A line drawn parallel to the elastic part from a strain of 0.002 meets the curve at 300 MPa. A part made from it will carry 270 MPa in service. Is that load safe from permanent deformation, and what elastic strain will the part show? The marks shown are an AskSia study allocation, not a University marking scheme.
Landmarks on a tensile curve.Landmarks on a tensile curve. The straight segment is elastic, the dashed line runs parallel to it from a strain of 0.002 and meets the curve at the yield strength, M marks the tensile strength and F the fracture after necking.StrainStressYieldM (tensile strength)F0.002 offsetElasticNecking
Landmarks on a tensile curve. The straight segment is elastic, the dashed line runs parallel to it from a strain of 0.002 and meets the curve at the yield strength, M marks the tensile strength and F the fracture after necking.
  • +1The offset construction defines the yield strength, so yield is 300 MPa, not the 240 MPa end of the straight line.
  • +1Compare: 270 MPa is below 300 MPa, so the part does not yield.
  • +1Hooke's law gives strain = stress divided by E = 270 MPa divided by 100,000 MPa = 0.0027.
  • +1State the caution: the curve is already non-linear above about 240 MPa, so 0.0027 slightly underestimates the real strain.
The yield strength from the 0.002 offset is 300 MPa, so a 270 MPa service stress does not cause permanent deformation. Hooke's law gives an elastic strain of about 0.0027, which is a slight underestimate because the curve has already started to bend above the proportional limit.
Sia tip — Read yield where the offset line meets the curve, never where the straight part ends; the proportional limit is hard to locate, which is why the offset convention exists.
Glossary

Key terms

Entrepreneurship
Spotting an opening for a business, gathering what it needs and starting a venture that profits by serving customers.
Intrapreneurship
Entrepreneurial work, such as launching a new product line, done by employees inside an established company.
B2B Product
A product sold to allied industries as an input, usually designed at the molecular level and long-lived in the market.
B2C Product
A product sold to consumers, designed by choosing ingredients and product structure, with a shorter life cycle.
Yield Strength
The stress at which plastic deformation becomes significant, read where a line offset by a strain of 0.002 meets the curve.
Poisson's Ratio
The ratio of lateral contraction strain to axial strain in a loaded specimen.
Band Gap
The energy separating the filled valence band from the empty conduction band; above about 2 eV the solid is an insulator.
Donor State
An energy level just below the conduction band created by a five-valent impurity such as phosphorus in silicon.
Hall-Petch Equation
The relation giving yield strength as a constant plus a term in the inverse square root of grain diameter.
Technology Readiness Level
A nine-level metric for how close a technology is to deployment, from principles observed to a proven system.
Stage-Gate Process
A development process in which stakeholders review deliverables at each gate and advance, retain or cancel the project.
RAT2IO
A mnemonic for planning a task by its resources, activities, tools, time, information and objective.
Elevator Pitch
A persuasive description of a business idea, deliverable in about 60 seconds, naming problem, solution, customer and value.
FAQ

MCEE6000D FAQ

Is the final exam open book?

No. The course plan states the final exam is closed book, and that its multiple-choice, fill-in-the-blank and short questions depend on concepts held in memory. Lecture-note equations are supplied only for the long questions, so formulas need to be understood well enough to choose the right one, while definitions and thresholds must be memorised.

How much is the final exam worth compared with the project?

The final exam carries 45 per cent of the grade and the team design project carries 50 per cent, split into technical idea and manufacturing, market study with finance and organisation, the business plan write-up, and the presentation. Homework makes up the remaining 5 per cent, so the exam is the largest single component.

Can I use ChatGPT or other AI tools?

For the design project, yes: the course plan calls AI use almost unrestricted there and asks you to cite a tool when its contribution is significant. Homework is different, because it is meant as exercise for the mind and copying results from AI is not allowed. AI is also excluded from grading, and the plan recommends prompts built on goal, context, source and expectations.

What kind of calculations come up?

The first homework set shows the pattern: choosing a metal that stays elastic and within a contraction tolerance, choosing a wire metal that keeps a voltage drop small, and computing free-electron density and electron mobility. These use stress, Hooke's law, Poisson's ratio, resistance and the conductivity equation, all of which appear in the materials properties module.

Do the student projects matter for the exam?

Yes. The project announcement says a small number of final exam questions will be asked about the student projects, and the pitch deck files are posted on Canvas around 20 or 21 November. Reading every team's deck and noting its product, key material and customer is a cheap way to prepare for those questions.

How big are project teams and how are topics chosen?

Teams have four students, with about ten teams adjusted to final enrolment. Each team is given a baseline project by random draw, such as a sunscreen cream or a PEM electrolyser, but is encouraged to propose its own product, and the topic is fixed after the elevator pitch discussion in class in mid-October.

Which textbooks support the materials chapters?

The course plan lists Product and Process Design Principles by Seider and co-authors, Callister and Rethwisch's Materials Science and Engineering, and Shackelford's Materials Science for Engineers. The materials properties module gives its reading assignment by Callister section numbers, with Shackelford used for the thermoelectric effect.

What does the business plan have to contain?

The outline names five key components: products and innovation, production plan, marketing plan, business and finance, and management and organisation. The project announcement adds that a plan can have seven sections including an executive summary and appendices, must stay within 15 pages excluding appendices, and states each member's responsibilities on the cover.

Chapter questions

Questions students ask in each MCEE6000D chapter

What is the difference between entrepreneurship and intrapreneurship?
Both create new products and business lines, but an intrapreneur does it inside an established company. The lecture's comparison puts ownership with the company rather than the founder, personal risk low rather than high, resources strong rather than limited, and freedom moderate because the work must fit company strategy, with salary and bonus replacing a potentially large equity reward. Chapter 01 · Material Products and Entrepreneurship
What are the four primary sources of chemicals and materials?
Minerals, oil and gas, the air and water around us, and living organisms such as plants and animals. Every product in the supply chain chapter traces back to one of them, for example nitrogen from air for ammonia, ethylene from petroleum for polyester, and silica from quartz sand for silicon wafers and optical fibre. Chapter 02 · Chemical and Material Supply Chains
How do you find the yield strength from a stress-strain curve?
Draw a straight line parallel to the elastic part of the curve, starting at a strain of 0.002, and read the stress where that line meets the curve. The convention exists because the proportional limit, where plastic deformation first starts, is difficult to locate on a real curve. Chapter 03 · Mechanical Properties of Metals
What separates an insulator from a semiconductor?
The width of the band gap between the filled valence band and the empty conduction band. The module puts the line at about 2 eV: wider than that is an insulator, narrower is a semiconductor. Silicon at about 1.1 eV and germanium at about 0.7 eV are its semiconductor examples. Chapter 04 · Electrical Properties and Semiconductors
Why does a smaller grain size make a metal stronger?
Grain boundaries impede dislocation motion, and a fine-grained metal has more total boundary area than a coarse-grained one. Since plastic deformation is the movement of dislocations, blocking them raises yield strength. The Hall-Petch equation expresses the effect through the inverse square root of grain diameter, and fast cooling of molten metal is one way to get fine grains. Chapter 05 · Crystal Structure, Ceramics and Polymers
What are the three possible outcomes of a Stage-Gate review?
Advance the project to the next stage; hold it where it is while outstanding critical problems are fixed; or stop it when the need has gone or an obstacle makes it unworkable. The reviewers come from the technical, manufacturing and business sides, joined by legal, supply chain, and environment, health and safety people. Chapter 06 · Hierarchical Product Design Framework
What is the difference between a functional product and a device?
A device is the subset of functional products that material passes through, in at one point and out at another. Devices usually have more complicated shapes and so call on mechanical and electrical engineers as well as materials specialists. The module's devices are a desiccant dehumidifier, which takes moisture from air, and an electrolyser, which converts water into hydrogen and oxygen. Chapter 07 · Functional Products and Devices
What are the five steps of the design procedure?
Specify the product attributes and functions; convert them into property constraints and performance indicators by identifying the physicochemical phenomena; conceptualise the product through material selection and structural design; analyse the performance of alternative designs by modelling or prototyping; and design the manufacturing process, including unconventional processing techniques. Chapter 08 · Ideation and the Five-Step Design Procedure
Why was a reservoir patch chosen over a matrix patch?
The tincture contains a lot of alcohol, and adhesives are usually incompatible with alcohol, which the study confirmed when all three candidate adhesives shrank in it. A reservoir patch keeps the liquid behind a membrane, and placing the adhesive only around the edge stops the alcohol reaching it. Chapter 09 · Transdermal Patch Design for a Herbal Tincture
Why does more sodium hydroxide give bigger copper particles?
Sodium hydroxide converts part of the copper into copper hydroxide, which is extremely insoluble. Reduced on its own, the soluble copper-ammonia complex nucleates fast and gives particles of about 5 nm, while the hydroxide nucleates slowly and grows for longer, giving particles as large as 500 nm. More hydroxide shifts the mix towards larger particles. Chapter 10 · Copper Nanoparticle Paste for Printed Electronics
How is the design project graded?
It is worth 50 per cent of the course in four parts: technical idea and manufacturing at 15, market study with finance and organisation at 15, the business plan write-up at 10, and the presentation, slides and write-up, at 10. Separately, pitch decks are ranked by the instructor at 60 per cent and the class at 40 per cent. Chapter 11 · Business Plan, Pitch Deck and Term Project
Study strategy

How to study for the exam

Split revision by question type, because the final does. For the recall sections, build one page of definitions and thresholds from Chapters 1 to 8, the entrepreneurship definition, the four primary sources, the B2B and B2C contrasts, the 0.002 offset, the five per cent brittleness threshold, the 2 eV band-gap line, the TRL ladder and the five design steps, and test yourself on it closed book until nothing is missed.

For the long questions, redo the worked selections in Chapters 3 and 4 with your own numbers, always starting with the limit check and ending with a stated decision. Then read the two case-study chapters as worked versions of the design procedure: for each, name the function, the phenomenon, the property constraint and the material chosen.

Finally, read every team's posted pitch deck, because a few exam questions are set on them.

Study MCEE6000D with AI

Your AI Engineering tutor for MCEE6000D

Stuck on a hard MCEE6000D question? Sia is AskSia’s AI Engineering tutor — ask any MCEE6000D Entrepreneurship of Materials Technologies question and get a clear, step-by-step explanation grounded in how the course is actually taught and assessed. Read this whole study guide free, then take your hardest questions to Sia.

A+Everything unlocked
Unlocks this Bible + all 13 of your subjects at The Hong Kong University of Science and Technology, plus 1,000+ more Bibles across the AskSia library.
Sia - your MCEE6000D tutor, unlimited, worked the way the exam marks it
The full 49-page Bible + practice bank with worked solutions
Chrome extension - sync your LMS so Sia knows your deadlines
Bilingual EN / Chinese on every Bible and every Sia answer
$0.99 Trial
30-day money-back · cancel in one tap · how it works