University of Birmingham · FACULTY OF MATHEMATICS

27887 Chap.5 Maclaurin and Taylor Series

- one subject, every graph, every model, every mark
6 Chapters3-page Bible
Our own words - no uploaded lecturer files
Updated for this semester
Chapter 5 of 11 · 27887

Maclaurin and Taylor Series

Polynomials that copy a function

A Maclaurin series rebuilds a function near zero from its value and derivatives there: the constant term matches the value, the linear term the slope, the quadratic term the curvature, and so on. A Taylor series does the same around any other point.

Truncating the series gives a polynomial model, and a past example question used exactly this to describe a transistor amplifier's output for a small input, up to and including the cubic term.

Where marks are lost

The 2016-17 feedback found that most candidates knew the structure of a Taylor series.

Marks went on the derivatives feeding it: chain-rule errors in the first derivative and product or quotient errors in the second. When a question supplies a higher derivative, it is a check on your own work; the report notes that integrating it to recover the lower derivatives does not give the correct answer.

Where it is tested

Taylor series share the fifth Möbius quiz with integration.

On longer papers the series is usually one step in an applied model, such as describing an amplifier for a small input, and it is followed by a calculation that uses the truncated polynomial. Accurate higher derivatives are therefore the real test, since every coefficient of the series depends on them.

In this chapter

What this chapter covers

  • 01

    Maclaurin series from derivatives at zero

  • 02

    Taylor series about a general point

  • 03

    Truncating a series to a stated power

  • 04

    Accuracy close to and far from the centre

  • 05

    Standard series for exponential, sine, cosine and logarithm

  • 06

    Series for products and composite functions

Worked example · free

Approximating sin 1 with one and two series terms

Q [3 marks]. AskSia-authored practice. Using the Maclaurin series of sin x, estimate sin 1 with the polynomials P₁ = x and P₃ = x − x³/6, and compare each with the true value 0.841. The marks shown are an AskSia study weighting, not an official University mark allocation.
Figure 5.1.Figure 5.1. Near the origin both polynomials hug sin x, but the straight line P₁ drifts away quickly while the cubic P₃ stays within 0.01 of the curve for |x| up to 1; beyond that every truncated series eventually leaves the curve.xyP₁ = xP₃ = x − x³/6sin xsin 1 = 0.841
Figure 5.1. Near the origin both polynomials hug sin x, but the straight line P₁ drifts away quickly while the cubic P₃ stays within 0.01 of the curve for |x| up to 1; beyond that every truncated series eventually leaves the curve.
  • 1Derivatives of sin x at zero cycle through 0, 1, 0, −1, so the series is x − x³/3! + x⁵/5! − and so on.
  • 1P₁(1) = 1, an error of about 0.159.
  • 1P₃(1) = 1 − 1/6 = 0.833, an error of about 0.008.
Adding the cubic term cuts the error by a factor of about twenty, from 0.159 to 0.008. The improvement is large because the neglected terms carry high powers of x that are small near the expansion point.
Sia tip — A derivative that is zero at the centre removes its term; do not treat the missing x² term as a mistake.
Glossary

Key terms

Taylor Series
A power series in (x − a) whose coefficients are the derivatives of a function at x = a divided by factorials.
Truncated Series
A finite polynomial formed by keeping only the terms of a series up to a stated power.
Expansion Point
The value of x about which a series is built, where its accuracy is greatest.
Factorial
The product of the whole numbers from 1 up to n, written n!, which divides the nth term of a series.
Small-Signal Approximation
A model that keeps only the first few series terms because the input stays close to the expansion point.
FAQ

Maclaurin and Taylor Series FAQ

How many terms should my series include?

Exactly as many as the question asks for, such as up to and including the term in x³. The truncation is part of the answer, so adding or omitting terms changes the model being described.

What is the difference between a Maclaurin and a Taylor series?

A Maclaurin series is a Taylor series centred at zero. A Taylor series uses powers of (x − a) and derivatives at x = a, which is useful when the function is easiest to evaluate at a point other than zero.

What should I do if the question gives me the third derivative?

Use it to check your own differentiation before you substitute. The 2016-17 feedback warns that integrating a supplied higher derivative to find the lower ones does not give the correct answer.

Study strategy

Exam move

Memorise the standard series for eˣ, sin x, cos x and ln(1 + x) together with the derivative values that produce them. For each new function, compute four derivatives carefully with the product and chain rules, then cross-check the result by multiplying or substituting into the standard series. Plot or tabulate one truncated series against its function to see where the approximation fails.

If a question supplies a higher derivative, compare it with your own value before you substitute anything, and if the two disagree, recheck the chain or product rule in the step that produced it.

Working through Maclaurin and Taylor Series in 27887? Sia is AskSia’s AI Mathematics tutor — ask any 27887 Maclaurin and Taylor Series question and get a clear, step-by-step explanation grounded in how 27887 is taught and assessed. Read this chapter free, then take your hardest questions to Sia.

A+Everything unlocked
Unlocks this Bible + all 17 of your subjects at University of Birmingham, plus 1,000+ more Bibles across the AskSia library.
Sia - your 27887 tutor, unlimited, worked the way the exam marks it
The full 3-page Bible + practice bank with worked solutions
Chrome extension - sync your LMS so Sia knows your deadlines
Bilingual EN / Chinese on every Bible and every Sia answer
$0.99 Trial
30-day money-back · cancel in one tap · how it works