38004 Chap.8 Improvement, Lean Operations and Agility
Improvement, Lean Operations and Agility
Improvement as a gap to close
The Week 5 lecture treats improvement as narrowing the distance between current and desired performance.
It sets two routes side by side: breakthrough change through business process re-engineering, which redesigns a process from first principles, and continuous improvement through repeated plan, do, check, act cycles or the data-driven Six Sigma sequence of define, measure, analyse, improve and control.
Lean and just-in-time
Lean operations aim to deliver exactly what customers want, in the right amount, place and time, at the lowest possible cost.
They rely on synchronised flow, customer pull, the removal of waste and steady improvement. Just-in-time is presented as a philosophy that attacks ordering, set-up and holding costs, the very costs that push firms towards large batches and buffer stock.
Agility and quality
Agile operations emphasise flexibility: responding to uncertain demand, customising, shortening development lead times and scaling output.
The lecture closes with dimensions of product and service quality and with total quality management, which builds quality into every process instead of inspecting it afterwards. It also recalls a major vehicle recall as a warning of what happens when early quality signals are ignored in favour of growth.
What this chapter covers
- 01
Importance and performance gaps
- 02
Re-engineering versus continuous improvement
- 03
PDCA and Six Sigma DMAIC
- 04
Lean flow, pull and waste
- 05
Delivery frequency and average stock
- 06
Agility, quality dimensions and TQM
Worked example · free
Average stock under weekly and daily delivery
- 2Average stock is half the delivery: 1,000 motors for weekly supply and 200 for daily supply.
- 2Holding cost is £0.50 times average stock: £500 a week against £100 a week.
- 2Add delivery cost: one trip at £60 gives £560; five trips at £60 give £400, so daily is £160 cheaper here.
Key terms
- Continuous Improvement
- An approach that raises performance through many small, repeated cycles of change rather than one large redesign.
- Business Process Reengineering
- Radical redesign of a business process from scratch in search of dramatic gains in cost, quality, service and speed.
- Pull Scheduling
- Control of flow in which each stage takes material only when it needs it, so use triggers replenishment.
- Just-in-Time
- A philosophy of producing and delivering items only when they are needed, attacking the costs that cause buffer stock.
- Time Compression
- Shortening the time an operation takes to satisfy demand, which is especially important for innovative products with short lives.
Improvement, Lean Operations and Agility FAQ
How does business process re-engineering differ from continuous improvement?
Re-engineering rethinks a process from first principles and seeks dramatic, discontinuous gains, reviewing people, technology and organisation together. Continuous improvement makes many small changes through repeated cycles. The lecture warns that planned breakthroughs do not always deliver the hoped-for improvement, so the actual gain can fall well short of the plan.
What are the stages of the Six Sigma improvement cycle?
Define the problem and the goal, measure the inputs and outputs, analyse to find and confirm root causes, improve by developing and testing a solution, and control by setting standards so the gain holds. Data and statistical analysis sit at every stage, which separates it from improvement driven by opinion.
What counts as waste in lean operations?
Waste is anything beyond the minimum equipment, materials, parts, space and labour time that add value to the product. Storage, inspection, delay, queuing and defective output add none, so they are treated as pure waste. Variability matters too, because irregular flow and inexact supply force managers to hold buffers that hide problems.
Why might daily deliveries cost more than weekly ones?
Smaller, more frequent deliveries cut average stock and holding cost, but every extra trip adds delivery cost. If the cost per trip stays high, the savings on stock can be swamped. Lean supply therefore works on reducing the cost of each delivery, for example by sharing routes, before shrinking batch sizes further.
What makes an operation agile rather than lean?
Agility stresses changing state efficiently as demand shifts: quick response, customisation, shorter development lead times, fast changeovers and scaling output up or down. Lean stresses efficient flow with minimal waste. The lecture suggests the right emphasis depends on the product and its operating context, especially how uncertain demand is.
Exam move
Draw the two improvement routes on one sheet: re-engineering with its promise and its risk, and the PDCA and DMAIC cycles with one sentence per stage. Then rebuild the delivery-frequency grid from memory, starting from the rule that average stock is half the delivery quantity, and change one input at a time to see which pattern wins.
Write down the lean concepts as a short list and attach a real example of waste you have seen to each type. Finally, pick a product with uncertain demand and argue in five sentences whether lean or agile principles should lead, naming the flexibility you would build and the quality dimension customers would notice first.
A final check: explain to a classmate why lowering stock exposes problems instead of solving them, and which problem you would fix first.
Working through Improvement, Lean Operations and Agility in 38004? Sia is AskSia’s AI Management tutor — ask any 38004 Improvement, Lean Operations and Agility question and get a clear, step-by-step explanation grounded in how 38004 is taught and assessed. Read this chapter free, then take your hardest questions to Sia.