40366 Chap.8 Capacitors and Basic LED Circuits
Capacitors and Basic LED Circuits
Building capacitors from office materials
The electrical properties lab has two halves. In the first, groups of two or three design, build and test plate capacitors from foil and everyday insulating sheets, and must produce four of them: a standard working device, an improved version, the largest capacitance they can achieve and the smallest working device.
For each one they record a dimensioned sketch, the materials, a predicted capacitance, the measured value and the reasons the two differ.
The relation behind every prediction
Capacitance equals the permittivity of free space times the relative permittivity of the dielectric times the plate overlap area, divided by the gap.
It therefore grows with area and permittivity and shrinks as the plates move apart, and the units must be metres and square metres for the answer to arrive in farads.
From components to working circuits
The second half identifies resistors from their colour bands and builds LED circuits on a breadboard powered at 5 V.
Students learn which holes are joined inside the board, put the LED's long leg on the live side, have the demonstrator check the circuit before power is applied, observe how changing resistors alters the brightness, and finish by designing a switch arrangement for several coloured LEDs.
What this chapter covers
- 01
What capacitors do in aircraft and everyday circuits
- 02
Building a foil plate capacitor
- 03
Capacitance from permittivity, area and gap
- 04
Predicted versus measured capacitance
- 05
Resistor colour bands
- 06
Breadboard rails, rows and the trench
- 07
Series and parallel resistors with an LED
- 08
Switching several LEDs
Worked example · free
Predict the readings of a capacitive fuel-level probe
- 1Area: 0.080 m × 0.050 m = 0.0040 m²; gap: 0.50 mm = 0.00050 m.
- 1Covered: C = ε₀εᵣA ÷ d = 8.85 × 10⁻¹² × 2.5 × 0.0040 ÷ 0.00050.
- 1C = 1.77 × 10⁻¹⁰ F, which is 177 pF.
- 1Drained: only the permittivity changes, from 2.5 to 1.0, so C falls in the same ratio: 177 ÷ 2.5 = 70.8 pF.
- 1The probe distinguishes the two states by a fall of about 106 pF.
Key terms
- Capacitance
- Charge stored per volt across two conductors, measured in farads and usually quoted in picofarads for small plates.
- Dielectric
- Insulating layer between capacitor plates whose relative permittivity multiplies the stored charge.
- LED Anode
- Longer leg of a light-emitting diode, which must face the positive supply for the diode to conduct and light.
- Breadboard Rail
- Long strip of holes along the edge of a breadboard, connected along its length and used for the supply or ground.
- Current-Limiting Resistor
- Series resistor chosen so that an LED carries no more than its safe current from a given supply.
Capacitors and Basic LED Circuits FAQ
What does a capacitor do in an aircraft or everyday circuit?
It stores electrical energy between two conductors separated by an insulator. That lets it hold a reserve of charge, smooth out ripples in a supply voltage and set the timing of many circuits; in aerospace systems capacitors also help stop sudden voltage spikes from damaging critical equipment.
Why must the foil tabs of the two plates never touch?
Each tab connects to one plate, and if the two meet the plates are joined directly, which short-circuits the device so it stores no charge between them. Tabs should leave the stack on opposite sides, and paper or card over the outer faces stops accidental contact during testing.
Which way round does an LED go on the breadboard?
The longer leg is the anode and goes towards the positive supply, on the live side of the central trench; the shorter leg goes towards ground. If the diode is reversed it simply stays dark, so check its direction first when a circuit fails.
How do I read the colour bands on a resistor?
Hold the resistor so the gold or silver tolerance band is on the right, because it is always last. Read the first two bands as digits and the third as the number of zeros to add, so grey, red and brown give 820 ohms.
What should I check before switching on an LED circuit on the breadboard?
Confirm that the supply was set to 5 V with nothing attached, that the LED's long leg sits on the live side of the trench, and that a resistor is in series with the diode. Then ask the demonstrator to inspect the board before connecting the supply and raising the current slowly.
Assessment move
Practise the capacitance relation until unit conversion is automatic: work three cases that change area, gap and permittivity one at a time and predict the factor before calculating. Then sketch the breadboard from memory, marking which holes are joined, and draw the schematic of a one-LED circuit with its resistor. Decode a handful of resistor colour codes, and size a current-limiting resistor for a different supply voltage.
Before the lab, decide how you will record each capacitor's dimensions, materials, predicted and measured values, so the discrepancy discussion writes itself afterwards. After the session, write one paragraph comparing your best and worst capacitor, naming which of area, gap or permittivity explains most of the difference, and keep it with your circuit sketches.
Working through Capacitors and Basic LED Circuits in 40366? Sia is AskSia’s AI Engineering tutor — ask any 40366 Capacitors and Basic LED Circuits question and get a clear, step-by-step explanation grounded in how 40366 is taught and assessed. Read this chapter free, then take your hardest questions to Sia.