BENG0003 Chap.2 Units, Conversions and Engineering Calculations
Units, Conversions and Engineering Calculations
Units, Conversions and Engineering Calculations covers the Week 7 and Week 8 toolkit that every later calculation in the module depends on. It starts with substantial and natural variables, the seven SI base quantities and the derived units for force, pressure, energy and power, then uses dimensions to test whether an equation even makes sense.
A multiply-by-one routine handles conversions, with special attention to the imperial units that appear in exam scenarios: pounds, cubic feet, inches, poise and centipoise, pound-force and revolutions per minute. The concentration section works through moles and molar mass, mass and mole fractions, percentages by weight and volume, ppm and the stock dilution equation used to make up media supplements.
The Reynolds number is treated for both pipes and stirred tanks, with separate critical values for each geometry and the step that turns a kinematic viscosity into a dynamic one.
The chapter closes with data analysis: mean, standard deviation, coefficient of variation, percent error, random against systematic error, and accuracy against precision, plus the decimal-place and working rules that protect marks in the Moodle quiz and the written exam.
What this chapter covers
- 01
SI base quantities, derived units and dimensions
- 02
Dimensional consistency and adding like units only
- 03
Conversion factors and imperial unit traps
- 04
Moles, fractions, percentages and ppm
- 05
Stock dilutions for media supplements
- 06
Reynolds number for pipes and stirred tanks
- 07
Mean, standard deviation, CV and percent error
- 08
Random and systematic error, accuracy and precision
Worked example · free
Impeller Reynolds number from tip speed and kinematic viscosity
- 1Impeller diameter: D = 0.75 ft × 12 in ft⁻¹ × 2.54 × 10⁻² m in⁻¹ = 0.2286 m.
- 2Rotational speed from tip speed: the tip travels πD per revolution, so N = 1.47 m s⁻¹ ÷ (π × 0.2286 m) = 2.05 s⁻¹ (2.0469 s⁻¹ kept for the next step).
- 1Density: specific gravity 1.05 means ρ = 1.05 × 1000 kg m⁻³ = 1050 kg m⁻³.
- 2The viscosity has units of length squared per time, so it is kinematic; the dynamic viscosity is μ = ρν = 1050 kg m⁻³ × 2.32 × 10⁻⁴ m² s⁻¹ = 0.2436 kg m⁻¹ s⁻¹.
- 1Impeller Reynolds number: Reᵢ = ρND²/μ = (1050 kg m⁻³ × 2.0469 s⁻¹ × 0.052258 m²) ÷ 0.2436 kg m⁻¹ s⁻¹ = 461.06.
- 1For a stirred tank, laminar flow lies at about 10 or below and turbulence needs about 10,000 or above, so 461 is transitional.
Key terms
- Dimensional consistency
- The requirement that every term added or subtracted in an equation carries identical dimensions and units.
- Conversion factor
- A ratio worth exactly one, such as 0.4536 kg per lb, that changes a unit while leaving the quantity unchanged.
- Dynamic viscosity
- Resistance of a fluid to shear, measured in Pa s or kg m⁻¹ s⁻¹, which sits in the denominator of the Reynolds number.
- Coefficient of variation
- Standard deviation expressed as a percentage of the mean, so spreads recorded in different units can be compared.
- Systematic error
- Bias that pushes every reading the same way and cannot be revealed by repeating the measurement.
Units, Conversions and Engineering Calculations FAQ
Do I need to memorise unit conversion factors for the exam?
No. The exam FAQ says conversion factors are printed at the end of the paper, and the Moodle quiz supplies Appendix A of Doran. You must, however, remember the concentration equations and the Reynolds number formulas, because no equation sheet is issued. Practise writing the factors as fractions so the units cancel visibly.
What Reynolds number makes flow turbulent in a pipe compared with a stirred tank?
The Week 7 lecture gives different critical values for each geometry. Pipe flow is laminar below 2,100 and turbulent above 4,000 on the lecture rule, although the module mock-quiz answer key used 10,000 for a pipe. Impeller flow in a stirred tank is laminar at about 10 or less and turbulent at about 10,000 or more. Anything between the limits is transitional, so always name the geometry first.
How do I turn kinematic viscosity into dynamic viscosity?
Multiply the kinematic value, in m² s⁻¹, by the fluid density in kg m⁻³ to get dynamic viscosity in kg m⁻¹ s⁻¹. Convert imperial units such as ft² s⁻¹ first by squaring the length factor. In the module's model answer for an impeller Reynolds number, spotting this step earned 3 of the 9 marks.
How many decimal places should I give in calculation answers?
Two decimal places are normally enough for final answers unless a question states otherwise, and intermediate steps can keep more significant figures. Quiz items may ask for powers of ten in a set format such as 5.0 x 10^3, so read each instruction and convert to the requested unit before rounding.
What happens if I do not upload my workings for the Moodle quiz?
The final question of the A1 quiz is a mandatory upload worth 30 marks. Skipping it, or uploading an unreadable or unrelated file, costs those 30 marks, and each answer given without its supporting calculation loses 2.5 marks. The portal takes Word, pdf or jpeg uploads, ten files at most.
Exam move
Treat this chapter as a skills drill rather than reading. Build one sheet of conversion factors you actually meet in questions: lb to kg, ft³ to m³, inch to metre, poise and centipoise, rpm to s⁻¹. Then practise chained conversions until you write every factor as a fraction without thinking.
Memorise the molarity, mass concentration and C₁V₁ = C₂V₂ relations, and test yourself on a supplement dilution where the stock is in mg mL⁻¹ and the target in ng mL⁻¹. For Reynolds numbers, solve one pipe case, one impeller case with a kinematic viscosity and one inverse case for minimum agitation speed, and say the regime aloud with the right threshold for the geometry.
Finish by computing a mean, standard deviation and CV by hand, and explain whether the scatter or the offset is the bigger problem.