University College London · FACULTY OF ENVIRONMENTAL SCIENCE

BENV0140 Chap.1 Energy Demand and Problem Solving

- one subject, every graph, every model, every mark
6 Chapters3-page Bible
Our own words - no uploaded lecturer files
Updated for this semester
Chapter 1 of 9 · BENV0140

Energy Demand and Problem Solving

Energy Demand and Problem Solving establishes the method used throughout the module. Energy demand begins with a service, such as warmth, light, mobility or clean air, and continues through equipment, delivered energy and the wider supply system. Power measures a rate, while energy accumulates that rate over time.

A clear system boundary determines which conversions, losses, behaviours and network effects enter the analysis. The chapter applies a five-stage loop: understand the problem, draw a diagram, devise a strategy, execute it step by step, then review and verify. That final stage checks units, scale and whether the proposed result still meets the occupant or system need.

A demand comparison is only meaningful when its interval, denominator and service are explicit. Annual consumption, an evening peak and a short control event can describe the same building while supporting different decisions. Students should therefore label every quantity before calculating, distinguish coincident loads from sequential ones, and state what can move without degrading the service.

Nested boundaries also matter: a device-level reduction may shift losses or constraints into the building, feeder or generation system. A strong answer closes the loop by translating the numerical result into the relevant capacity, cost, carbon or comfort implication and naming the evidence that would test it.

In this chapter

What this chapter covers

  • 01

    Energy services

  • 02

    Power and energy

  • 03

    System boundaries

  • 04

    Demand profiles

  • 05

    Five-stage problem solving

  • 06

    Verification and interpretation

Worked example · free

Separate daily energy from coincident power

Q [6 marks]. Marks shown organise this original practice answer and are not a published assessment scheme. A 1.8 kW heater runs for five hours, a 0.12 kW fan for ten hours and a 0.9 kW hob for forty minutes. Find total energy and the peak when all operate together.
The arrows move from an energy resource to a delivered carrier, conversion and occupant service, while the return arrow shows how operation and feedback can chaThe arrows move from an energy resource to a delivered carrier, conversion and occupant service, while the return arrow shows how operation and feedback can change demand. primary energyresourcedeliveredenergyuseful energyconversionoccupantservicefeedback changes demand
The arrows move from an energy resource to a delivered carrier, conversion and occupant service, while the return arrow shows how operation and feedback can change demand.
  • 3Calculate 9.00 kWh for the heater, 1.20 kWh for the fan and 0.60 kWh for the hob.
  • 1Add energy to obtain 10.80 kWh for the day.
  • 1Add overlapping power to obtain a 2.82 kW coincident peak.
  • 1Explain that shifting the hob can reduce peak power without changing daily energy.
Daily energy is 10.80 kWh and the coincident peak is 2.82 kW. The practice marks are an original allocation, not a UCL marking scheme.
Sia tip — Convert every duration to hours before multiplying, then add power only across periods that overlap.
Glossary

Key terms

Energy service
The useful outcome that energy helps deliver to a person or system.
Power
The rate at which energy is transferred or used.
Demand profile
The pattern of energy or power demand across time.
FAQ

Energy Demand and Problem Solving FAQ

Why are power and energy separated?

Power describes the rate at a moment or interval, so it governs equipment and network capacity. Energy accumulates that rate over time and connects to fuel use, bills and emissions. Two loads can use the same energy while creating very different peaks if their operating times differ.

How do I choose a system boundary?

Choose the smallest boundary that answers the stated decision, then name important effects outside it. An appliance boundary may suit a power calculation, while a decarbonisation claim may need conversion losses, supply timing, network constraints and occupant service included.

What does verification involve?

Check dimensional consistency, arithmetic direction, order of magnitude and the service objective. Recalculate one step in reverse where possible. Then ask whether the answer changes when a key assumption, time interval or boundary is altered.

Study strategy

Exam move

Begin each revision problem with a four-line set-up: required service, system boundary, time interval and requested quantity. Draw the energy chain from resource or carrier to equipment and service. Label every value as power or energy before using it.

Practise conversions between watts, kilowatts, watt-hours, kilowatt-hours and megajoules, but keep the physical story visible rather than treating conversion as a separate trick. Build pairs of examples with equal daily energy and different peaks so the capacity consequence becomes intuitive. For qualitative cases, use the five-stage loop as headings and finish with a verification step that names evidence.

Record mistakes under time conversion, non-overlapping load, boundary mismatch or missing interpretation. In integrated questions, connect a building decision to the wider system only after the local service has been protected. A strong closing sentence says whether demand falls, shifts or merely changes carrier, and identifies the metric needed to confirm that claim.

Create a small library of demand profiles for a heater, fan, cooker, vehicle charger and hot-water store. For each one, change the start time without changing energy, then change operating duration while holding useful service constant. These variations reveal which interventions reduce consumption and which only alter coincidence.

Next, practise drawing nested boundaries around the same situation: device, dwelling, feeder and national system. List the new flows, losses and constraints added at each layer. This exercise makes it easier to challenge claims that a local efficiency or fuel switch automatically improves the whole system. For problem-solving practice, deliberately insert one error and find it during review.

Use an impossible unit, omit a load or choose a duration that does not match the question. Explain which check catches it. Finally, write two short conclusions for the same calculation, one for an occupant and one for a network planner. The number remains unchanged, but the decision relevance differs.

That translation builds the course habit of applying common physical evidence to several perspectives without losing the original service need.

A+Everything unlocked
Unlocks this Bible + all 32 of your subjects at University College London, plus 1,000+ more Bibles across the AskSia library.
Sia - your BENV0140 tutor, unlimited, worked the way the exam marks it
The full 3-page Bible + practice bank with worked solutions
Chrome extension - sync your LMS so Sia knows your deadlines
Bilingual EN / Chinese on every Bible and every Sia answer
$0.99 Trial
30-day money-back · cancel in one tap · how it works
BENV0140 · Fundamentals of Smart Energy and the Built Environment - independent study guide on the AskSia Library. More University College London subjects · Microeconomics across all universities