ELEC6103 Chap.6 Communications Payload, Transponders and Antennas
Communications Payload, Transponders and Antennas
Why the payload sets capacity
Everything a satellite earns passes through its payload: the antennas that collect and radiate microwave signals, and the transponders between them. A transponder is a receive and transmit chain that boosts a weak uplink carrier, moves it to a new frequency and sends it to the ground.
The rest of the spacecraft only keeps this chain alive, so the payload design decides how much traffic the satellite can sell.
Inside a C band transponder
The first stage after the receive antenna is a low noise amplifier, placed there because it fixes the noise performance of everything behind it.
Filtering isolates one channel, a downconverter subtracts 2,225 MHz, so the 5,925 to 6,425 MHz uplink lands on 3,700 to 4,200 MHz, and a travelling wave tube amplifier supplies the output power. The frequency change is essential: retransmitting on the receive frequency would let the strong output drown the receiver.
Channels on the second polarisation sit 20 MHz to one side, interleaving with the first set.
Bent pipe against on-board processing
A bent-pipe transponder never inspects the signal, which makes it simple and lets future ground modulation schemes use an old satellite, but uplink noise and interference travel through untouched.
An on-board processor demodulates to baseband, reads each packet header, switches it to the addressed downlink beam and regenerates clean bits.
It stops uplink noise from accumulating and enables routing between beams, at the price of fixing the signal format at launch.
Four antenna families
Wire antennas such as monopoles give near-omnidirectional coverage for telemetry and command, which matters when the satellite is not yet pointed.
Horns produce wide beams, including the roughly 17° global beam, yet struggle beyond about 23 dB of gain or below a 10° beam.
Reflectors give the narrow spot beams common on geostationary satellites, and phased arrays steer beams electronically by adjusting each element's phase.
Gain, beamwidth and reuse
Three relations carry most questions: G = η(πD/λ)2, a 3 dB beamwidth of about 75λ/D degrees, and the reflector shortcut G ≈ 33,000/θ2.
A narrow beam needs a large dish, and a higher frequency shrinks the dish for the same beam. Spatially separated beams and orthogonal polarisations let a large satellite use its spectrum up to twenty times over, while spare receivers and amplifiers protect a payload that can never be repaired.
What this chapter covers
- 01
Payload role and what a transponder does
- 02
C band frequency plan and the 2,225 MHz translation
- 03
Polarisation offset and why the frequency must change
- 04
Bent-pipe and on-board processing transponders compared
- 05
Wire, horn, reflector and phased array antennas
- 06
Gain, beamwidth and the 33,000 over theta squared estimate
- 07
Sizing transmit and receive dishes for one beam
- 08
Frequency reuse by beams and polarisation, and payload redundancy
Worked example · free
Dish diameters and gain for a 2.5 degree Ku band beam
- 2Find the wavelengths from 0.3 / f(GHz): 0.025 m at 12 GHz and 0.02143 m at 14 GHz.
- 2Rearrange the beamwidth relation to D = 75 x wavelength / beamwidth and size the transmit dish.
- 2Repeat for the receive dish on the higher uplink frequency.
- 2Apply G = 33,000 / theta squared and convert the ratio to decibels.
Key terms
- Transponder
- A receiver and transmitter chain on the satellite that amplifies an incoming uplink carrier, translates it to the downlink frequency and sends it back towards the ground.
- Bent-Pipe Transponder
- A linear transponder that only amplifies and frequency-shifts the signal without demodulating it, so it works with any ground modulation but passes uplink noise straight to the downlink.
- On-Board Processing
- A transponder design that demodulates the uplink to baseband, routes packets by their header to the correct downlink beam and regenerates the bits before retransmission.
- Half-Power Beamwidth
- The angle between the two directions where the main lobe of an antenna pattern has dropped by 3 dB from its peak; in this course it is estimated as 75 wavelengths over diameter, in degrees.
- Frequency Reuse
- Using the same band more than once on one satellite, through spot beams far enough apart not to interfere and through orthogonal polarisations within a beam, up to about twenty times.
Communications Payload, Transponders and Antennas FAQ
Why must a transponder change the frequency before retransmitting?
The output leaving the satellite is many orders of magnitude stronger than the faint carrier arriving from the ground. If both used the same frequency, the transmitted power would leak into the receive chain and overwhelm it. Shifting C band traffic down by 2,225 MHz keeps transmit and receive bands well separated, so filters can isolate the sensitive low noise amplifier from the high power stage.
When would a designer choose on-board processing over a bent pipe?
Processing pays off when capacity, flexible routing between many spot beams, or protection from uplink noise matter most, as in large multibeam broadband systems. Because it regenerates the data, noise on the uplink does not add to downlink noise. A bent pipe remains attractive for long missions where future ground standards are unknown, since it relays any waveform and has fewer complex parts.
Why can a horn not provide a narrow spot beam?
Horns become impractical once the requirement passes roughly 23 dB of gain or a beam tighter than about 10 degrees, because the aperture grows too large for a simple flared waveguide. That limit suits the wide global beam around 17 degrees, where a horn is natural. Narrower spot beams therefore come from reflectors, often fed by horns, or from phased arrays.
How does a phased array steer its beam without moving?
Each small radiating element has its own phase shifter. With identical phase settings across the array, the radiated waves add up straight ahead along the axis. Introducing a constant phase increment from one element to the next tilts the direction in which they reinforce, so changing the increment scans the beam electronically, with no motors or gimbals needed.
Why do sidelobes matter for a geostationary antenna?
Even a highly directional antenna leaks some energy outside its main lobe. Geostationary neighbours can sit only about two degrees apart along the arc, so energy in the sidelobes can reach or pick up signals from an adjacent satellite. Interference control therefore depends on sidelobe levels as well as on main lobe gain, which is why antenna patterns are plotted in decibels against angle.
Exam move
Draw the C band transponder chain from memory, labelling the low noise amplifier, filter, downconverter and travelling wave tube, then sketch the frequency plan with 5,925 to 6,425 MHz mapping onto 3,700 to 4,200 MHz and the 20 MHz polarisation offset. Write a six-line comparison of bent pipe against on-board processing that ends with when you would pick each.
For the antenna questions, practise turning a beamwidth into diameters at both the uplink and downlink frequency of one band, and always state whether your gain is a ratio or in dB. Finish with one reuse calculation: bandwidth times number of beams times two polarisations.
Working through Communications Payload, Transponders and Antennas in ELEC6103? Sia is AskSia’s AI Electrical Engineering tutor — ask any ELEC6103 Communications Payload, Transponders and Antennas question and get a clear, step-by-step explanation grounded in how ELEC6103 is taught and assessed. Read this chapter free, then take your hardest questions to Sia.