The University of Hong Kong · FACULTY OF ELECTRICAL ENGINEERING

ELEC6103 Chap.10 Digital Transmission, Eb/No, Modulation and DVB-S2

- one subject, every graph, every model, every mark
9 Chapters5-page Bible
Our own words - no uploaded lecturer files
Updated for this semester
Chapter 10 of 11 · ELEC6103

Digital Transmission, Eb/No, Modulation and DVB-S2

Why satellite links went digital

The lecture gives four motives for abandoning analogue transmission: digital signals tolerate noise better, use bandwidth more efficiently, allow errors to be corrected and adapt easily to different services.

Once a link is digital, its quality is judged by bit error rate, and the ratio that predicts it is Eb/N0, the energy carried by each information bit over the noise power in one hertz.

That ratio makes schemes with different bandwidths directly comparable, which plain C/N cannot do.

Moving between Eb/N0 and C/N

Because energy per bit is carrier power divided by bit rate, and noise density is kT, the two ratios differ only by the spectral efficiency R/B. In decibels you add 10 log(R/B) to Eb/N0 to get C/N.

If the link carries more than one bit per hertz the required C/N is the larger number; below one bit per hertz it is the smaller. This conversion lets you turn a demodulator threshold into a link budget target.

Bits per symbol and the cost in power

A modulator packs bits into symbols: one for BPSK, two for QPSK, three for 8-PSK and four for 16-APSK.

Bandwidth follows the symbol rate, so higher orders squeeze more data into the same spectrum. The penalty is geometric. With fixed signal power, more phases on one circle sit closer together, noise can push a symbol across to its neighbour more easily, and the receiver needs a higher C/N for the same error rate.

Gray coding limits the damage so a nearest-neighbour mistake flips one bit.

From information rate to occupied spectrum

The calculation runs in a fixed order. Divide the information rate by the FEC rate times bits per symbol to get the symbol rate, multiply by one plus the roll-off to get the occupied bandwidth, then divide the information rate by that bandwidth for efficiency.

Noise is computed in the symbol-rate bandwidth because the matched receive filter is shaped to the symbols.

What DVB-S2 adds

DVB-S2 combines a tighter roll-off, higher-order modulations and LDPC coding, which reaches a given error rate at a lower Eb/N0. In the lecture's DBS comparison this more than doubles throughput in the same bandwidth with more margin.

Amplifier back-off and adaptive coding and modulation complete the picture.

In this chapter

What this chapter covers

  • 01

    Four reasons satellite systems moved from analogue to digital

  • 02

    Eb/No as the figure of merit for a digital link

  • 03

    Converting Eb/No to C/N through spectral efficiency

  • 04

    Bits per symbol for BPSK, QPSK, 8-PSK and 16-APSK

  • 05

    Neighbour distance on a PSK constellation and Gray coding

  • 06

    Symbol rate, roll-off and occupied bandwidth in sequence

  • 07

    FEC rate, LDPC codes and choosing a MODCOD

  • 08

    DVB-S against DVB-S2 on the same DBS bandwidth

  • 09

    Output back-off and linearisation of the travelling wave tube

Worked example · free

One 512 kbps carrier under QPSK and under 8-PSK

Q [8 marks]. AskSia-authored practice. A data carrier has an information rate of 512 kbps, FEC rate 2/3 and a filter roll-off of 0.25. Work out its symbol rate, occupied bandwidth and spectral efficiency under QPSK, then repeat for 8-PSK, and state how much spectrum the change of modulation saves. The marks shown are an AskSia study allocation, not the University's marking scheme.
Each extra bit per symbol shrinks the bandwidth a carrier occupies.Each extra bit per symbol shrinks the bandwidth a carrier occupies. The bars hold one 256 kbps carrier at FEC 7/8 and a 40 per cent roll-off fixed and change only the modulation, so QPSK needs half the bandwidth of BPSK.occupied kHz409.6BPSK204.8QPSK136.58-PSK102.416-APSK
Each extra bit per symbol shrinks the bandwidth a carrier occupies. The bars hold one 256 kbps carrier at FEC 7/8 and a 40 per cent roll-off fixed and change only the modulation, so QPSK needs half the bandwidth of BPSK.
  • 2Information bits per symbol: QPSK gives 2 x 2/3 = 1.333; 8-PSK gives 3 x 2/3 = 2.0.
  • 2Symbol rates: QPSK 512 / 1.333 = 384 ksps; 8-PSK 512 / 2.0 = 256 ksps.
  • 2Occupied bandwidth = symbol rate x (1 + 0.25): QPSK 384 x 1.25 = 480 kHz; 8-PSK 256 x 1.25 = 320 kHz.
  • 2Spectral efficiency = 512 / bandwidth: QPSK 512 / 480 = 1.07 bits per hertz; 8-PSK 512 / 320 = 1.60 bits per hertz. The saving is 480 - 320 = 160 kHz, one third of the QPSK allocation.
With rate 2/3 coding, each QPSK symbol carries 2 x 2/3 = 1.333 information bits and each 8-PSK symbol carries 3 x 2/3 = 2.0. The QPSK carrier therefore runs at 512 / 1.333 = 384 ksps and occupies 384 x 1.25 = 480 kHz, an efficiency of 512 / 480 = 1.07 bits per hertz. Under 8-PSK the symbol rate is 512 / 2.0 = 256 ksps, the occupied bandwidth 256 x 1.25 = 320 kHz and the efficiency 512 / 320 = 1.60 bits per hertz. Switching to 8-PSK frees 160 kHz, a third of the QPSK allocation, but the denser constellation needs a higher C/N, so the saving is only usable if the link budget has that power to spare.
Sia tip — Strip the coding and the modulation before you add the roll-off; applying the 1.25 factor first gives the same bandwidth only by luck and hides the symbol rate that sets the noise bandwidth.
Glossary

Key terms

Eb/No Ratio
The ratio of energy carried by each information bit to the noise power spectral density kT; the course uses it to compare modulation schemes and converts it to C/N by adding 10 log(R/B).
Symbol Rate
The number of modulated symbols sent per second, in baud; it equals the information rate divided by the FEC rate times the bits carried by each symbol.
Roll-off Factor
The excess bandwidth of the transmit filter beyond the symbol rate, written alpha; occupied bandwidth is the symbol rate times one plus alpha, and DVB-S2 allows values near 5 per cent.
Spectral Efficiency
Information rate divided by occupied bandwidth, in bits per hertz; operators care because transponder capacity is leased per hertz, so higher efficiency means less spectrum to rent.
Forward Error Correction
Redundant parity bits added before transmission so the receiver can detect and repair errors, quoted as useful bits over total bits, such as 3/4 or 7/8.
Output Back-off
Running a transponder amplifier below saturation so it stays nearly linear, typically about 1 dB for one PSK carrier and 3 dB when several FDMA carriers share it.
FAQ

Digital Transmission, Eb/No, Modulation and DVB-S2 FAQ

When is the required C/N lower than the required Eb/No?

The two ratios differ by 10 log of the bit rate over the noise bandwidth. When a scheme carries fewer than one information bit per hertz, that log term is negative, so the C/N target comes out below the energy-per-bit target. Efficient MODCODs above one bit per hertz reverse the order, pushing the required C/N above the Eb/No threshold.

Why does a higher-order modulation need more carrier power?

Adding points to a constellation of fixed amplitude shrinks the gap between neighbours: on equal circles, adjacent QPSK points sit about 1.41 radii apart while adjacent 8-PSK points are only about 0.77 radii apart. A smaller noise excursion then causes a decision error, so the receiver needs a stronger signal relative to the noise to hold the same bit error rate.

What made DVB-S2 so much better than DVB-S in the DBS example?

Three changes stack up. A much smaller roll-off wastes less spectrum around each carrier, higher-order modulations put more bits into each symbol, and low-density parity-check codes decoded iteratively reach a target error rate with less energy per bit than older codes. In the lecture's comparison the newer standard carries 44 Mbps instead of 20 Mbps in the same bandwidth while also holding more margin.

Why should margins on a strongly coded link be stated honestly?

Powerful codes give a very steep error curve. The lecture notes that a coded DVB-S signal moves from error-free reception to complete failure across a C/N change of under 1 dB, so there is almost no graceful degradation. A link budget that rounds optimistically by a decibel can turn a working design into one that drops out entirely at the first fade.

Study strategy

Exam move

Build a single table with rows for BPSK, QPSK, 8-PSK and 16-APSK and columns for bits per symbol, symbol rate, occupied bandwidth and efficiency, then fill it for one information rate, one FEC rate and one roll-off of your choosing. Repeat with a different code rate and watch which columns move.

Separately, practise converting a demodulator Eb/No threshold to a C/N target in both directions, checking the sign of 10 log(R/B) each time. Finish by explaining in three sentences why DVB-S2 beats DVB-S, naming roll-off, modulation order and LDPC, and add one line on back-off. Draw the QPSK and 8-PSK constellations from memory with Gray labels until the neighbour spacing argument is automatic.

Working through Digital Transmission, Eb/No, Modulation and DVB-S2 in ELEC6103? Sia is AskSia’s AI Electrical Engineering tutor — ask any ELEC6103 Digital Transmission, Eb/No, Modulation and DVB-S2 question and get a clear, step-by-step explanation grounded in how ELEC6103 is taught and assessed. Read this chapter free, then take your hardest questions to Sia.

A+Everything unlocked
Unlocks this Bible + all 52 of your subjects at The University of Hong Kong, plus 1,000+ more Bibles across the AskSia library.
Sia - your ELEC6103 tutor, unlimited, worked the way the exam marks it
The full 5-page Bible + practice bank with worked solutions
Chrome extension - sync your LMS so Sia knows your deadlines
Bilingual EN / Chinese on every Bible and every Sia answer
$0.99 Trial
30-day money-back · cancel in one tap · how it works