The Hong Kong University of Science and Technology · FACULTY OF ENGINEERING

MCEE6000D Chap.3 Mechanical Properties of Metals

- one subject, every graph, every model, every mark
7 Chapters4-page Bible
Our own words - no uploaded lecturer files
Updated for this semester
Chapter 3 of 11 · MCEE6000D

Mechanical Properties of Metals

Reading a tensile test

Stress is load over original area and strain is change in length over original length. Below the proportional limit a metal deforms elastically and Hooke's law links the two through the modulus of elasticity; a stretched bar also narrows, and Poisson's ratio relates that contraction to the axial strain.

Because the proportional limit is hard to locate, yield strength is read where a line parallel to the elastic slope, offset by a strain of 0.002, crosses the curve.

The tensile strength is the curve's maximum, after which necking leads to fracture.

Selection and service

The chapter works a homework-type selection: find the stress, rule out alloys that would yield, then compute each survivor's diameter change against a tolerance.

It then covers ductility as percent elongation, with a fracture strain below five per cent read as brittle, hardness by indentation, fatigue failure below static strength under fluctuating stress, the S-N curve and fatigue limit, and creep at elevated temperature with its three stages before rupture.

In this chapter

What this chapter covers

  • 01

    Stress, strain and Hooke's law

  • 02

    Poisson's ratio and lateral contraction

  • 03

    Yield by the 0.002 offset

  • 04

    Tensile strength, necking and fracture

  • 05

    Selecting an alloy against two limits

  • 06

    Ductility and the brittleness threshold

  • 07

    Hardness, fatigue and creep

Worked example · free

Elastic stretch and thinning of a steel tie rod

Q [3 marks]. AskSia-authored practice. A steel tie rod 2.5 m long and 20 mm in diameter carries a stress of 150 MPa, below its yield strength. With E = 207 GPa and Poisson's ratio 0.30, find its elongation and its reduction in diameter. The marks shown are an AskSia study allocation, not a University marking scheme.
Landmarks on a tensile curve.Landmarks on a tensile curve. The straight segment is elastic, the dashed line runs parallel to it from a strain of 0.002 and meets the curve at the yield strength, M marks the tensile strength and F the fracture after necking.StrainStressYieldM (tensile strength)F0.002 offsetElasticNecking
Landmarks on a tensile curve. The straight segment is elastic, the dashed line runs parallel to it from a strain of 0.002 and meets the curve at the yield strength, M marks the tensile strength and F the fracture after necking.
  • +1Axial strain = 150 MPa divided by 207,000 MPa = 7.25 times 10 to the minus 4.
  • +1Elongation = strain times 2500 mm = 1.81 mm.
  • +1Lateral strain = 0.30 times 7.25 times 10 to the minus 4 = 2.17 times 10 to the minus 4, so the diameter shrinks by 0.0043 mm.
The rod lengthens by about 1.81 mm and its diameter shrinks by about 0.0043 mm. Both results are elastic, so they disappear when the load is removed.
Sia tip — Confirm the stress is below yield before using Hooke's law; above yield the elastic relations no longer describe the deformation.
Glossary

Key terms

Modulus of Elasticity
The constant of proportionality between stress and strain in elastic deformation, also called Young's modulus.
Tensile Strength
The maximum stress on the engineering stress-strain curve, after which necking begins.
Percent Elongation
Ductility expressed as the change from original to fracture length, divided by the original length, times 100.
Fatigue Limit
The stress amplitude below which a material can survive an infinite number of cycles without fatigue failure.
Creep
Time-dependent deformation under static stress at elevated temperature, important for metals above about 0.4 of the melting temperature.
Necking
Local narrowing of a tensile specimen after the tensile strength is passed, leading to fracture.
FAQ

Mechanical Properties of Metals FAQ

How do you find the yield strength from a stress-strain curve?

Draw a straight line parallel to the elastic part of the curve, starting at a strain of 0.002, and read the stress where that line meets the curve. The convention exists because the proportional limit, where plastic deformation first starts, is difficult to locate on a real curve.

When is a metal considered brittle?

When it shows little plastic deformation before fracture. The module gives a working threshold: a fracture strain below about five per cent is often treated as brittle. Ductility itself is reported as percent elongation, using the original length and the length at fracture.

Can a part fail below its yield strength?

Yes, by fatigue. Under dynamic, fluctuating stresses, as in bridges, aircraft and machine parts, failure can occur at stress levels well below the static yield or tensile strength. The S-N curve shows that fewer cycles are survived at higher stress, and some materials have a fatigue limit below which they last indefinitely.

What does the hardness number tell you?

Hardness measures resistance to a small local dent or scratch. A test presses a small indenter into the surface under a controlled load and loading rate, then measures the depth or size of the mark. A softer metal leaves a larger, deeper indentation and so gets a lower hardness number, such as a lower HB value.

Study strategy

Exam move

Sketch the stress-strain curve from memory with the offset line, M and F marked, then redo the alloy selection with new numbers until the order of checks is automatic: stress, yield comparison, then the tolerance. Label the three creep stages on a sketch as a final self-test.

Working through Mechanical Properties of Metals in MCEE6000D? Sia is AskSia’s AI Engineering tutor — ask any MCEE6000D Mechanical Properties of Metals question and get a clear, step-by-step explanation grounded in how MCEE6000D is taught and assessed. Read this chapter free, then take your hardest questions to Sia.

A+Everything unlocked
Unlocks this Bible + all 13 of your subjects at The Hong Kong University of Science and Technology, plus 1,000+ more Bibles across the AskSia library.
Sia - your MCEE6000D tutor, unlimited, worked the way the exam marks it
The full 4-page Bible + practice bank with worked solutions
Chrome extension - sync your LMS so Sia knows your deadlines
Bilingual EN / Chinese on every Bible and every Sia answer
$0.99 Trial
30-day money-back · cancel in one tap · how it works