MCEE6000D Chap.4 Electrical Properties and Semiconductors
Electrical Properties and Semiconductors
Conduction from the outside in
Ohm's law ties current to voltage through resistance, and resistance splits into a material property, resistivity, and the specimen's length and area. Conductivity is the reciprocal of resistivity.
The band picture explains why it varies so much: copper has empty states right beside its filled ones, magnesium has overlapping bands, an insulator has a band gap above about 2 eV, and a semiconductor a gap below it.
Carriers and doping
Silicon and germanium, with gaps of about 1.1 and 0.7 eV, conduct by both electrons and holes, so conductivity is a sum of two terms, each a concentration times the electronic charge times a mobility.
Holes move less freely than electrons, for two reasons the module gives. Doping with a five-valent atom such as phosphorus adds a donor level just below the conduction band and makes n-type material without creating holes; a three-valent atom such as boron adds an acceptor level just above the valence band and makes p-type material without creating free electrons.
The chapter works a wire-selection problem and two carrier calculations of the homework type.
What this chapter covers
- 01
Ohm's law, resistivity and conductivity
- 02
Band structures of conductors, insulators and semiconductors
- 03
Intrinsic semiconduction in silicon and germanium
- 04
Electron and hole mobility
- 05
Sizing a wire against a voltage drop
- 06
Donor and acceptor doping
Worked example · free
Voltage drop along a copper lead
- +1Area = pi times (0.5 times 10 to the minus 3 m) squared = 7.85 times 10 to the minus 7 square metres.
- +1Resistance = length divided by (conductivity times area) = 30 divided by 47.1 = 0.637 ohm.
- +1Voltage drop = current times resistance = 3.0 times 0.637 = 1.91 V.
Key terms
- Resistivity
- The material property that, with a specimen's length and cross-section, sets its electrical resistance.
- Fermi Energy
- The energy of the highest filled electron state at 0 K.
- Electron Mobility
- A measure of how freely free electrons drift in a field, reduced by scattering at lattice imperfections.
- Acceptor State
- An energy level just above the valence band created by a three-valent impurity such as boron in silicon.
- Intrinsic Semiconductor
- A pure semiconductor in which each excited electron leaves a hole, so both carry current.
- Extrinsic Semiconductor
- A semiconductor whose conduction is controlled by deliberately added impurity atoms.
- Hole
- A quasiparticle representing a missing electron in the valence band, whose motion reflects many electrons shifting.
- Band Structure
- The arrangement of allowed electron energy bands and gaps that decides how readily a solid conducts.
Electrical Properties and Semiconductors FAQ
What separates an insulator from a semiconductor?
The width of the band gap between the filled valence band and the empty conduction band. The module puts the line at about 2 eV: wider than that is an insulator, narrower is a semiconductor. Silicon at about 1.1 eV and germanium at about 0.7 eV are its semiconductor examples.
Why is hole mobility usually lower than electron mobility?
The band that holes travel through is a more complicated, less favourable path for fast drift, and a hole is a quasiparticle whose apparent motion results from many electrons shifting position. That is less direct than the motion of a single free electron, so holes drift more slowly in the same field.
What does an n-type dopant actually add?
A five-valent atom such as phosphorus uses four electrons for bonding with silicon and leaves one loosely bound, creating a donor level just below the conduction band. That electron is easily excited into conduction, and no matching hole is created in the valence band, which is why the material conducts mainly by electrons.
How do I find the free-electron concentration of a metal?
Work out how many atoms sit in a cubic metre from the density, Avogadro's number and the atomic weight, then multiply by the number of free electrons each atom contributes. With that concentration and the measured conductivity, the electron mobility follows by dividing conductivity by the concentration times the electronic charge, since the hole term is negligible in a metal.
Exam move
Write the four forms of Ohm's law and the two-term conductivity equation from memory, then redo the wire sizing for a different length. Finish by drawing the four band diagrams and labelling where donor and acceptor levels sit. Time yourself on the mobility calculation so it takes under five minutes.
Working through Electrical Properties and Semiconductors in MCEE6000D? Sia is AskSia’s AI Engineering tutor — ask any MCEE6000D Electrical Properties and Semiconductors question and get a clear, step-by-step explanation grounded in how MCEE6000D is taught and assessed. Read this chapter free, then take your hardest questions to Sia.