University of Birmingham · FACULTY OF ENGINEERING

40366 Chap.4 Flight Forces and Autopilot Feedback

- one subject, every graph, every model, every mark
7 Chapters3-page Bible
Our own words - no uploaded lecturer files
Updated for this semester
Chapter 4 of 12 · 40366

Flight Forces and Autopilot Feedback

A simulator for engineers

The A5 lab uses a professional desktop flight simulator, the same program students use in later modules. The aim is not piloting skill but an understanding of the controls, the instruments and how an aircraft responds; crashing while learning is expected and the flight is simply reset.

Students work individually through three activities in order and rate their own progress rather than plotting data.

Feedback control

An autopilot is a closed-loop controller: the pilot sets a target, instruments measure the actual value, the difference becomes an error signal, and motors move the controls until the error disappears.

Modes split into longitudinal ones such as altitude hold and vertical speed and lateral ones such as heading hold. The light aircraft used has no autothrottle, so climbing on autopilot bleeds away airspeed and the pilot must manage power to avoid a stall.

Forces in flight

Four forces act on the aircraft: lift reacting weight and thrust opposing drag. When height and speed are both held steady, both pairs balance.

The simulator computes these forces in pounds-force, which students convert to newtons to sketch a free-body diagram, the starting point for every performance calculation in the degree. Later questions ask what changes when power, climb rate or aircraft mass changes.

In this chapter

What this chapter covers

  • 01

    Joystick axes, throttle and flight school lessons

  • 02

    Why engineers study handling rather than flying

  • 03

    The autopilot as a closed-loop feedback controller

  • 04

    Heading, altitude and vertical speed modes

  • 05

    Lift, weight, thrust and drag in equilibrium

  • 06

    Pound-force to newton conversion

  • 07

    Effects of power, climb and mass changes

Worked example · free

Free-body diagram for a light twin in level flight

Q [4 marks]. AskSia-authored practice. A simulator shows a light twin in steady level flight with 4,400 lbf of lift and 4,400 lbf of weight, and 520 lbf each of thrust and drag. Convert the forces to newtons, find the aircraft mass and its lift-to-drag ratio, and state the condition that makes the diagram valid. All marks shown are an AskSia study weighting and not an official University marking scheme.
Figure 4.1.Figure 4.1. Free-body diagram of an AskSia light twin in steady level flight. Lift and weight are equal at 19.6 kN, thrust and drag are equal at 2.31 kN; arrows within a pair match, but the two pairs are not to one scale.Lift 19.6 kNWeight 19.6 kNThrust 2.31 kNDrag 2.31 kNFlight direction
Figure 4.1. Free-body diagram of an AskSia light twin in steady level flight. Lift and weight are equal at 19.6 kN, thrust and drag are equal at 2.31 kN; arrows within a pair match, but the two pairs are not to one scale.
  • 1One pound-force is 9.81 ÷ 2.205 = 4.449 N, so lift and weight are 4,400 × 4.449 ≈ 19,576 N, about 19.6 kN.
  • 1Thrust and drag are 520 × 4.449 ≈ 2,313 N, about 2.31 kN.
  • 1Mass = weight ÷ g = 19,576 ÷ 9.81 ≈ 1,996 kg; lift-to-drag ratio = 4,400 ÷ 520 ≈ 8.5.
  • 1Record the readings only after speed and altitude have stopped changing, so the two balanced pairs describe a genuine equilibrium.
Lift and weight are each about 19.6 kN, thrust and drag each about 2.31 kN, the mass is about 1,996 kg and the lift-to-drag ratio is about 8.5. Record the readings only after the aircraft has settled into steady flight.
Sia tip — Convert every simulator force with 4.449 N per lbf before drawing the arrows, and label each arrow in newtons.
Glossary

Key terms

Free-Body Diagram
Sketch isolating one object with an arrow for each external force acting on it, the basis for writing force balances.
Closed-Loop Control
Control scheme that measures its own output, compares it with a target and acts on the difference until they agree.
Altitude Hold
Autopilot mode that keeps the aircraft at the height it was flying when the mode was engaged.
Pound-Force
Customary unit of force used by the simulator, equal to about 4.449 newtons.
Autothrottle
Speed control loop that adjusts engine power automatically, much like cruise control in a car.
FAQ

Flight Forces and Autopilot Feedback FAQ

Do I need to be a good pilot to do well in the flight simulator lab?

No flying skill is expected. The lab is about how controls, instruments and autopilot modes affect the aircraft, and losing control while learning is normal; the flight is simply reset. Engineers need to understand how an aircraft is designed to be flown safely, not to fly it themselves.

How does an autopilot work as a feedback loop?

The pilot enters a target such as a heading or altitude. Instruments measure what the aircraft is actually doing, the controller turns the difference into an error signal, and motors move the controls. The loop repeats until the error is zero and the aircraft matches the target.

Why does airspeed fall when the autopilot climbs the aircraft?

Climbing converts some of the energy from the engine into height, and on a light aircraft with no autothrottle nothing adds power automatically. Speed therefore drops in a climb and rises in a descent, and too steep a climb can bring the aircraft close to a stall.

How do I convert simulator forces from pounds-force to newtons?

Multiply by 4.449, which is 9.81 divided by 2.205. A drag reading of 300 lbf, for example, becomes about 1,335 N. Do the conversion before drawing the free-body diagram so every arrow carries SI units.

What are the four forces on an aircraft in level flight?

Lift from the wings acts upward against the weight, and thrust from the engine acts forward against aerodynamic drag. When height and speed are both held steady, lift equals weight and thrust equals drag, so the free-body diagram shows two balanced pairs.

Study strategy

Assessment move

Before the session, sketch a blank free-body diagram and write the pound-force conversion beside it so you are ready to fill it in. In the lab, take the flying school lessons slowly, then spend time changing autopilot setpoints and watching how speed responds, since that is the clearest demonstration of feedback and of energy trading between speed and height. Record force readings only once the aircraft is steady.

Afterwards, redraw the diagram neatly in newtons, compute the lift-to-drag ratio, and check that the weight divided by g gives a sensible mass. Note any questions you still have on your self-evaluation form, and take them to a demonstrator before the next simulator session.

Working through Flight Forces and Autopilot Feedback in 40366? Sia is AskSia’s AI Engineering tutor — ask any 40366 Flight Forces and Autopilot Feedback question and get a clear, step-by-step explanation grounded in how 40366 is taught and assessed. Read this chapter free, then take your hardest questions to Sia.

A+Everything unlocked
Unlocks this Bible + all 17 of your subjects at University of Birmingham, plus 1,000+ more Bibles across the AskSia library.
Sia - your 40366 tutor, unlimited, worked the way the exam marks it
The full 3-page Bible + practice bank with worked solutions
Chrome extension - sync your LMS so Sia knows your deadlines
Bilingual EN / Chinese on every Bible and every Sia answer
$0.99 Trial
30-day money-back · cancel in one tap · how it works
40366 · LC Practical and Design Skills for Materials Science/Aerospace Engineering - independent study guide on the AskSia Library. More University of Birmingham subjects · Microeconomics across all universities