University of Birmingham · FACULTY OF ENGINEERING

40366 Chap.6 Metallography and Grain Size Measurement

- one subject, every graph, every model, every mark
7 Chapters3-page Bible
Our own words - no uploaded lecturer files
Updated for this semester
Chapter 6 of 12 · 40366

Metallography and Grain Size Measurement

Why microstructure is worth the effort

Grain size, the balance of phases and the defects inside a metal connect what it is made of and how it was processed to how it behaves under load.

The metallography lab gives each group a carbon steel already mounted in Bakelite and ground to 1200 grit, and asks for three things: a properly prepared surface, a grain size measurement and an estimate of composition from the phases seen.

From scratches to grains

Preparation runs from a rough polish to a fine one.

A rough polish with a 6 µm abrasive takes out the grinding scratches, a fine polish at 0.25 µm removes the rough-polish marks, the sample is cleaned between stages and checked under the optical microscope, and staff supervise an etch in 2% Nital that reveals the structure.

Measuring what you see

Grain size is found with the Heyn linear intercept method: random test lines, a count of boundary crossings and a division of true length by that count, with at least 50 grains counted overall.

Images of all three samples need scale bars. Phase fractions measured with image analysis software then place each steel on the low-carbon side of the iron-carbon diagram, where the lever rule converts the pearlite fraction into a carbon content, assuming only ferrite and pearlite are present.

In this chapter

What this chapter covers

  • 01

    Microstructure as the link between processing and properties

  • 02

    Grinding, rough polishing and fine polishing

  • 03

    Etching with Nital to reveal grains

  • 04

    The Heyn linear intercept method

  • 05

    Scale bars and representative fields

  • 06

    Ferrite and pearlite in carbon steels

  • 07

    The lever rule below 0.76 wt% carbon

Worked example · free

Compare horizontal and vertical intercepts on a ceramic micrograph

Q [5 marks]. AskSia-authored practice. On a print of an alumina ceramic micrograph, the 50 µm scale bar measures 10 mm. A horizontal test line 80 mm long crosses 22 grain boundaries between its ends and its far end lies exactly on a boundary. A vertical line of the same length crosses 12 boundaries. Find both mean intercepts and say what they reveal about the grain shape. The marks shown are AskSia's own study weighting, not an official University allocation.
Figure 6.1.Figure 6.1. An AskSia alumina ceramic micrograph with a horizontal 80 mm test line, equal to 400 µm at the scale shown. Red dots mark 22 boundary crossings and the far end scores a half, so the horizontal mean intercept is 400 ÷ 22.5 = 17.8 µm; the near-vertical boundaries hint at elongated grains.Test line 400 µm22 boundary crossings50 µmStart: not countedEnd on boundary: ½
Figure 6.1. An AskSia alumina ceramic micrograph with a horizontal 80 mm test line, equal to 400 µm at the scale shown. Red dots mark 22 boundary crossings and the far end scores a half, so the horizontal mean intercept is 400 ÷ 22.5 = 17.8 µm; the near-vertical boundaries hint at elongated grains.
  • 1Scale: 10 mm on the print is 50 µm, so each printed millimetre is 5 µm and each 80 mm line is 400 µm.
  • 1Horizontal count: the start is not counted and the far end on a boundary scores one half, so N = 22.5.
  • 1Horizontal intercept: 400 ÷ 22.5 = 17.8 µm.
  • 1Vertical intercept: 400 ÷ 12 = 33.3 µm.
  • 1Ratio 33.3 ÷ 17.8 = 1.9: the grains are nearly twice as long vertically, so both directions must be measured and reported.
The horizontal intercept is 17.8 µm and the vertical one 33.3 µm. The difference shows elongated grains, so a single horizontal line would understate their size; place lines in several directions and base the average on enough grains in total.
Sia tip — Convert the line with the scale bar before dividing; a printed magnification can be wrong once an image is resized.
Glossary

Key terms

Microstructure
Arrangement of grains, phases and defects in a material as seen at small scales under a microscope.
Pearlite
Layered mixture of ferrite and iron carbide that forms when carbon steel cools slowly through the eutectoid point.
Ferrite
Body-centred cubic iron holding very little carbon, the light-etching constituent in a slowly cooled low-carbon steel.
Lever Rule
Tie-line calculation that gives the proportion of each phase from the overall composition and the two phase-boundary compositions.
Rough Polishing
Polishing stage with a coarser abrasive, here 6 µm, whose job is to remove the scratches left by grinding.
FAQ

Metallography and Grain Size Measurement FAQ

Why does my polished steel still show scratches under the microscope?

Straight parallel scratches usually mean the coarse polishing stage stopped before the grinding damage was gone. The finer abrasive that follows is too gentle to remove those marks, so go back a stage, check the whole surface under the microscope, clean the sample and only then return to fine polishing.

How many grains should I count for a reliable grain size?

The lab script asks for at least 50 grains in total, which usually means several test lines placed at random and in different directions. Record each line's true length and its crossing count, add them up, and divide the total length by the total count to get one mean intercept.

Do the ends of a test line count as grain boundary crossings?

Normally they do not, because an end point is simply where you stopped drawing. The exception is an end that lands exactly on a boundary, which is scored as half a crossing. Mark these cases on your print so a reader can follow the count.

Why is the Nital etch done with a member of staff?

Nital is an acid solution, so the etching step is carried out under the support of staff, with the protective equipment they specify and their instructions on handling and timing. Treat it as a supervised step: have your polished, clean sample ready and wait for the demonstrator before starting.

Why must every metallography image include a scale bar?

Grain size and spacing are lengths, and without a scale nobody can convert a measurement on the screen or print into micrometres. A scale bar survives resizing, whereas a magnification figure becomes wrong as soon as the image is enlarged or shrunk in a report.

Study strategy

Assessment move

Rehearse the preparation sequence until you can explain what each stage removes and why the order cannot be reversed. Then practise the intercept method on any grain image: draw lines in at least two directions, count crossings with the end-point rule, convert with the scale bar and compare the directions.

Finish with a lever-rule calculation from a stated carbon content to the expected pearlite fraction, using the tie line just above the eutectoid, and write one sentence on its assumptions. Keep your micrographs, counts and calculations together in one table so they can go straight into a report.

Before the session, sketch what a ferrite and pearlite structure should look like at two magnifications, so you know what a representative field is when you see it.

Working through Metallography and Grain Size Measurement in 40366? Sia is AskSia’s AI Engineering tutor — ask any 40366 Metallography and Grain Size Measurement question and get a clear, step-by-step explanation grounded in how 40366 is taught and assessed. Read this chapter free, then take your hardest questions to Sia.

A+Everything unlocked
Unlocks this Bible + all 17 of your subjects at University of Birmingham, plus 1,000+ more Bibles across the AskSia library.
Sia - your 40366 tutor, unlimited, worked the way the exam marks it
The full 3-page Bible + practice bank with worked solutions
Chrome extension - sync your LMS so Sia knows your deadlines
Bilingual EN / Chinese on every Bible and every Sia answer
$0.99 Trial
30-day money-back · cancel in one tap · how it works
40366 · LC Practical and Design Skills for Materials Science/Aerospace Engineering - independent study guide on the AskSia Library. More University of Birmingham subjects · Microeconomics across all universities