40366 Chap.2 Oscillation, Friction and Flywheel Energy
Oscillation, Friction and Flywheel Energy
Four stations, one method
The A1 mechanics lab sends small groups round four activities: a mass bouncing on a spring, pendulums of different lengths and masses, a sled pulled along a runway, and a flywheel spun by a falling mass. Everyone takes a turn at the hands-on work and everyone leaves with a full set of results. Each activity hides a quantity inside an equation.
Three of the four rearrange it into a straight line and read the quantity from a gradient, while the pendulum station calculates gravity case by case.
Vibration and resonance
The spring shows simple harmonic motion, whose period depends on the mass and the stiffness through the relation in the script.
The pendulum confirms that period depends on length and gravity but not on the bob, and pairs of pendulums hung from a flexible line demonstrate resonance.
For aircraft and spacecraft these ideas govern structural vibration, flutter and pilot induced oscillation.
Friction and rotation
Pulling force plotted against normal force gives the coefficient of friction as a gradient, measured once for starting from rest and once for sliding, and the two values are compared.
The flywheel converts gravitational energy into linear and rotational kinetic energy and back again; its moment of inertia comes from a gradient, and the rebound height measures efficiency. Most stations end with reflection questions, several of them on errors, so careful notes during the session pay off later.
What this chapter covers
- 01
Simple harmonic motion of a mass on a spring
- 02
Spring stiffness from period against the square root of mass
- 03
Pendulum period, length and gravity
- 04
Resonance and how designers avoid it
- 05
Static and kinetic coefficients of friction
- 06
Linear and angular motion analogues
- 07
Flywheel moment of inertia from a gradient
- 08
Energy conversion and efficiency
Worked example · free
Calibrate a gimbal isolator and weigh an unknown payload
- 2Least-squares gradient through the origin: sum of products 2.182 divided by sum of squares 6.96 gives 0.314 seconds per root kilogram.
- 1Gradient equals 2π over the square root of k, so k = (2π ÷ 0.3135)² = 20.0² ≈ 400 N/m.
- 2Read the payload off the line: √m = 0.47 ÷ 0.3135 = 1.50, so m = 1.50² ≈ 2.25 kg.
- 1The payload is about 0.25 kg heavier than labelled, and 1.50 lies inside the calibrated range of 1.0 to 1.6, so the reading can be trusted.
Key terms
- Simple Harmonic Motion
- Oscillation in which the restoring force is proportional to displacement, giving a period that does not depend on amplitude.
- Resonance
- Growth of amplitude when a repeated force arrives at the natural frequency of the system it acts on.
- Spring Constant
- Stiffness of a spring expressed as the force needed per metre of extension, in newtons per metre.
- Kinetic Friction
- Resisting force between two surfaces already sliding over each other, measured in the lab by tapping the panel so the sled keeps moving.
- Flywheel Efficiency
- Ratio of rebound height to release height in the falling-mass test, showing how much stored energy survives one cycle.
Oscillation, Friction and Flywheel Energy FAQ
How do I find spring stiffness from a period graph?
Rearrange the period equation so that period is proportional to the square root of mass, plot those two quantities, and fit a line. The gradient equals 2π divided by the square root of the stiffness, so square 2π over the gradient to recover k in newtons per metre.
Why does the pendulum period not depend on the mass of the bob?
For small swings the restoring effect of gravity and the inertia of the bob both scale with mass, so mass cancels. Only the effective length, measured to the centre of the bob, and the gravitational acceleration remain in the period equation.
What does the gradient of pulling force against normal force give?
It gives the coefficient of friction for the pair of surfaces under test, because friction equals the coefficient multiplied by the normal force. The sled is tested once without tapping the panel and once while tapping it, giving separate static and kinetic lines that the script asks you to compare.
How is efficiency defined for the flywheel station?
Efficiency is the useful energy you get out divided by the energy you put in. For the falling mass both energies are mass times gravity times a height, so the ratio reduces to rebound height over release height, a number between 0 and 1 normally quoted as a percentage.
Why does resonance matter so much for aircraft?
A structure forced near its natural frequency builds up large motions that can break it. Flutter, which links aerodynamic loads to wing bending and twisting, limits the maximum permitted airspeed, and spacecraft are designed stiff enough to stay clear of launch vibration.
Assessment move
Before the session, write the four equations from the script and, for each, decide which pair of quantities you will plot and what the gradient will equal. In the lab, time many oscillations rather than one, repeat the flywheel drops, and note anything that disturbs a reading. Afterwards fit each line, check whether it passes through the origin, and compare the fitted value with the reference figure in the script.
Write one sentence on the size of the difference and one on its most likely cause, naming the specific reading involved. Finally, reread the aerospace application notes and connect each station to a real aircraft or spacecraft problem. Keep these analyses together, since any of them could become the basis of a later write-up.
Working through Oscillation, Friction and Flywheel Energy in 40366? Sia is AskSia’s AI Engineering tutor — ask any 40366 Oscillation, Friction and Flywheel Energy question and get a clear, step-by-step explanation grounded in how 40366 is taught and assessed. Read this chapter free, then take your hardest questions to Sia.