BIOL10401 Chap.3 Spectrophotometry and Absorption Spectra
Spectrophotometry and Absorption Spectra
Spectrophotometry and Absorption Spectra follow light from the lamp through wavelength selection, sample and detector. A scanning measurement reveals where a compound absorbs and can support identification through a spectral pattern. A fixed-wavelength measurement quantifies absorbance at a chosen maximum.
The blank defines which background components are subtracted, while clean cuvette faces and the absence of bubbles protect the optical path. Peak position reflects molecular absorption behaviour; peak height changes with concentration under Beer-Lambert conditions. Dilution should reduce absorbance without moving the molecular maximum.
What this chapter covers
- 01
Lamp and monochromator
- 02
Cuvette light path
- 03
Blank selection
- 04
Scanning mode
- 05
Fixed-wavelength mode
- 06
Beer-Lambert reasoning
Worked example · free
Predict a diluted spectrum
- 2Keep the maximum at 520 nm because molecular identity is unchanged.
- 1Halve absorbance to about 0.60 within the linear range.
- 1Confirm blank and path length remain matched.
Key terms
- Absorbance
- Absorbance is a logarithmic measure comparing incident and transmitted light.
- Absorption maximum
- An absorption maximum is a wavelength at which a compound absorbs most strongly.
- Blank sample
- A blank sample contains background components without analyte.
Spectrophotometry and Absorption Spectra FAQ
Why does the blank matter?
The instrument subtracts the blank response from the sample response. A mismatched blank leaves solvent or background absorbance inside the result and changes the meaning of every peak.
Does dilution move an absorption maximum?
Ideal dilution reduces the number of absorbing molecules and therefore peak height, but it does not change the molecular transition energy that sets the wavelength maximum.
When should I use scanning mode?
Use a scan to inspect the absorption pattern across wavelengths and identify a useful maximum. Use fixed-wavelength mode when measuring concentration at a selected wavelength.
Exam move
Redraw the instrument as lamp, monochromator, cuvette and detector, then explain what information is created at each stage. Compare several blank choices and state exactly what each would subtract. Practise reading spectra by naming the horizontal wavelength axis before judging peak position and the vertical absorbance axis before judging concentration.
Use proportional dilution questions to separate changes in peak height from changes in wavelength. Review common optical faults such as fingerprints, bubbles, wet surfaces and off-scale absorbance by matching each symptom to the appropriate remedy. End every answer by stating whether the evidence concerns identity, concentration or both. Follow photons through the instrument when revising.
The lamp supplies a broad range, the monochromator selects a wavelength, the cuvette defines the sample path and the detector records transmitted light. Relate absorbance to the logarithm of incident over transmitted intensity so that lower transmittance means higher absorbance. A scan changes wavelength to reveal a spectral pattern; a fixed-wavelength reading holds wavelength constant for quantification.
This distinction resolves many distractors. Dilution should lower peak height within the linear range but should not move the molecular absorption maximum simply because fewer molecules are present. A shifted maximum therefore calls for an identity, chemical-state or instrument check. Treat blank selection as a subtraction question.
Write the contents of sample and reference side by side and cross out the components shared by both. An ethanol pigment extract needs the same ethanol background, while water would leave solvent absorption in the trace. A blank containing an analyte component can subtract that component and make a mixture appear incomplete. After reblanking, read a fresh blank as a sample and inspect whether its baseline behaves as expected.
Keep cuvette orientation, path length and solvent conditions constant when comparing spectra because Beer-Lambert proportionality assumes that concentration is not the only changing feature. Use a fault table with symptom, cause, correction and confirmation.
A broad baseline displacement suggests an unsuitable reference; an isolated disturbance may come from a bubble; fingerprints or turbidity can absorb or scatter outside the analyte response; off-scale absorbance requires a documented dilution into the validated range. Confirm cleaning or bubble removal by repeating the same sample.
Confirm dilution by checking that height changes approximately with concentration while peak position remains stable, then restore the dilution factor once. For mixtures, report whether the complete pattern agrees with expected compounds and state overlap as ambiguity. A coincident peak supports compatibility, not certain identity, and a concentration estimate needs an appropriate calibration relation.
Close a revision session by sketching two spectra that have the same maximum wavelength but different peak heights, then a third with a shifted maximum. Explain which comparison supports a concentration change and which requires an identity or chemical-state investigation.
Working through Spectrophotometry and Absorption Spectra in BIOL10401? Sia is AskSia’s AI Biology tutor — ask any BIOL10401 Spectrophotometry and Absorption Spectra question and get a clear, step-by-step explanation grounded in how BIOL10401 is taught and assessed. Read this chapter free, then take your hardest questions to Sia.