The University of Manchester · FACULTY OF ENGINEERING

CIVL13001 Chap.4 Axial Members and Truss Analysis

- one subject, every graph, every model, every mark
7 Chapters4-page Bible
Our own words - no uploaded lecturer files
Updated for this semester
Chapter 4 of 8 · CIVL13001

Axial Members and Truss Analysis

Axial Members and Truss Analysis uses imaginary cuts and isolated joints to find internal tension and compression. A consistent assumed-tension convention lets negative algebra identify compression. The method of joints advances through solvable nodes when many member forces are required, while the method of sections reaches selected forces directly.

Both methods depend on a valid pin-jointed, joint-loaded truss idealisation.

The joint method provides two planar force equations at each isolated node and works best when no more than two member forces are unknown. A sectioned truss provides two force equations and a moment equation, allowing a target member to be reached without solving the whole system.

Geometry must be resolved with direction ratios or angles referenced to the correct axis. Zero-force shortcuts require unloaded joints and exact collinearity conditions; they describe the current load case rather than permanent redundancy. Every negative result under an assumed-tension convention is reported as a positive compression magnitude.

Substitution at a final joint and comparison with the external reactions give independent closure. If loads act between joints or connections transfer moment, the two-force-member idealisation is no longer sufficient.

In this chapter

What this chapter covers

  • 01

    Axial cuts

  • 02

    Tension convention

  • 03

    Compression interpretation

  • 04

    Method of joints

  • 05

    Method of sections

  • 06

    Zero-force members

  • 07

    Truss-model limits

Worked example · free

Resolve a symmetric triangular truss

Q [6 marks]. A 30 kN load acts at the apex of a symmetric truss whose two inclined members follow 3-4-5 geometry. Find the member forces. The marks shown here are original study guidance and not an official University assessment scheme.
The same determinate truss supports two routes: joint equilibrium advances member by member, while the dashed section exposes only the crossed members needed foThe same determinate truss supports two routes: joint equilibrium advances member by member, while the dashed section exposes only the crossed members needed for a focused calculation.joint method startsat a solvable nodesection cut crossesselected memberscut
The same determinate truss supports two routes: joint equilibrium advances member by member, while the dashed section exposes only the crossed members needed for a focused calculation.
  • 1Use symmetry to obtain 15 kN vertical support reactions.
  • 3At the apex, assume both member forces act away from the joint and balance vertical components using 3/5.
  • 2The result is negative 25 kN under the tension assumption, so both members carry 25 kN compression.
Each inclined member carries 25 kN compression, with two 15 kN upward components balancing the apex load. The practice marks are not a University rubric.
Sia tip — Assume tension for every unknown member and translate a negative solution into a positive magnitude labelled compression.
Glossary

Key terms

Tension
An axial action that tends to lengthen a member.
Compression
An axial action that tends to shorten a member.
Section cut
An imaginary cut through a truss that exposes forces in selected crossed members.
FAQ

Axial Members and Truss Analysis FAQ

When is the method of joints efficient?

It is efficient when forces in most members are required and a joint with no more than two unknown member forces can be selected. Each solved force reduces unknowns at neighbouring joints.

When is the method of sections faster?

It is faster when only a few member forces are requested. Cut through the target and at most two other unknowns, then choose a moment centre that eliminates two crossed forces where possible.

What breaks the two-force-member model?

A load applied between joints, a curved member, a rigid moment-transferring connection or another action that creates bending means the member is not carrying pure axial force under the simple truss idealisation.

Study strategy

Exam move

Begin truss revision by checking the model rather than solving immediately. Confirm straight members, pin-like joints and loads applied at joints, then calculate external reactions. For the method of joints, circle a node with at most two unknowns, draw every member force away from the joint and resolve directions with a small geometry triangle.

Continue through neighbouring joints and finish at an already solvable node as a check. For the method of sections, sketch several possible cuts and select one that crosses the target plus no more than two other unknown members. Look for an intersection point that eliminates two unknown moments. Practise reporting negative assumed-tension results as compression magnitudes.

Add zero-force-member cases, but write the exact unloaded-joint condition before using a shortcut. Keep errors under wrong direction cosine, too many unknowns, missed reaction and invalid truss idealisation. Substituting the solved components back into both force directions should close each final joint. Build fluency with small direction triangles before tackling full trusses.

For each sloping member, write horizontal and vertical ratios beside the line and confirm which axis the quoted angle uses. Solve one symmetric truss by joints and then recover a central member with a section; agreement verifies both routes. Next break symmetry by changing one load and observe why the reactions and member forces no longer mirror.

Practise selecting a moment centre for a section cut by extending the unknown member lines lightly until two intersect. If they are parallel, accept that no finite intersection exists and choose a force equation or different cut. Maintain a member-force table with magnitude, tension or compression, and one component check.

Do not retain negative magnitudes in the final table when the sign has already been translated into compression. For zero-force rules, draw a counter-example with an external joint load so the condition is remembered with its boundary. Finish a session by changing the loading direction and predicting which zero member could become active.

This reinforces that zero force belongs to a load case, while the member may still provide stability and carry action under another case.

A+Everything unlocked
Unlocks this Bible + all 41 of your subjects at The University of Manchester, plus 1,000+ more Bibles across the AskSia library.
Sia - your CIVL13001 tutor, unlimited, worked the way the exam marks it
The full 4-page Bible + practice bank with worked solutions
Chrome extension - sync your LMS so Sia knows your deadlines
Bilingual EN / Chinese on every Bible and every Sia answer
$0.99 Trial
30-day money-back · cancel in one tap · how it works