EART60071 Chap.5 Aerosol Growth, Visibility and Particulate Matter
Aerosol Growth, Visibility and Particulate Matter
Aerosol Growth, Visibility and Particulate Matter follows a soluble particle as the air around it moistens and asks what that growth does to the view and to air-quality numbers. The simplified Köhler relation combines a solute factor, which lowers the equilibrium humidity, with a curvature factor, which raises it for small drops; mass conservation and additive volumes close the calculation of the wet diameter.
Extinction then scales with the square of diameter, so visual range falls as particles swell even when no new particles appear, while particulate mass scales with the cube, so a few large particles can dominate PM10. The chapter turns each relation into a step-by-step routine with the module's constants.
Questions in this area often change one quantity, such as humidity or particle size, and ask what happens to another, so the chapter stresses which power of diameter each result depends on.
What this chapter covers
- 01
Hygroscopic particles and their wet diameter
- 02
The solute and curvature factors in the Köhler relation
- 03
Solution density and wet diameter
- 04
Extinction coefficient and visual range
- 05
Particulate mass concentration
- 06
PM10 and PM2.5 under the simplified convention
Worked example · free
Visual range before and after humid growth
- 2σext = 2 × π(2 × 10−6)2/4 × 2 × 108 = 1.26 × 10−3 m−1.
- 1Vvis = 1.9/1.26 × 10−3 = 1512 m.
- 2At 3 µm extinction rises by (3/2)2 = 2.25 to 2.83 × 10−3 m−1, so the range falls to 672 m.
Key terms
- Hygroscopic growth
- The uptake of water by soluble aerosol particles as relative humidity rises, increasing their wet diameter.
- Kelvin effect
- The increase in equilibrium vapour pressure over a curved droplet surface compared with a flat one.
- Extinction coefficient
- The fractional loss of light per unit distance caused by particles scattering and absorbing it.
- Visual range
- The distance at which an object can just be seen, inversely related to the extinction coefficient.
- Van't Hoff factor
- The effective number of dissolved particles each solute unit contributes, two for sodium chloride.
Aerosol Growth, Visibility and Particulate Matter FAQ
What do the two factors in the Köhler relation do?
The first factor, moles of water over moles of water plus the van't Hoff factor times moles of solute, is the solute effect: dissolved material lowers the equilibrium vapour pressure. The exponential is the curvature effect, which raises it for small, strongly curved drops. In the module's ammonium sulphate example they give 0.833 and 0.842 respectively.
Why does humidity reduce visibility if no new particles appear?
Hygroscopic particles take up water and grow as humidity rises. In the simplified treatment extinction is proportional to the square of the diameter, so a modest increase in size produces a larger increase in extinction, and visual range, which is K divided by extinction, falls accordingly. The dry aerosol amount can be unchanged throughout.
How are PM10 and PM2.5 decided in the module exercises?
Real classifications use aerodynamic diameter, but the exercises treat the stated spherical diameter as the relevant size and each population as monodisperse. Every population below 10 micrometres counts towards PM10 and only those at or below 2.5 micrometres towards PM2.5, so a population of 5 micrometre particles adds to PM10 but not to PM2.5.
Why does a small change in diameter change mass so much?
A sphere's mass is proportional to the cube of its diameter, so doubling the diameter multiplies the mass eightfold. In a mixed haze a modest number of coarse particles can therefore carry most of the particulate mass while the fine particles carry most of the number, which is why PM10 can be large when PM2.5 is modest.
Exam move
Revise this chapter by building three short routines and running each several times. For Köhler growth: dry diameter to solute moles, a chosen water ratio to solution density, density to wet diameter, wet diameter into the relation; then compare the solute factor with the full answer and say what curvature contributed.
For visibility: diameter and number to extinction, extinction to range, and the effect of a stated growth factor. For particulate mass: number, density and diameter cubed, converted from kilograms to micrograms, then sorted into size classes. Keep the module constants together on one line of your notes: surface tension 0.075, extinction efficiency 2, contrast constant 1.9 and the compound table.
When a question changes humidity, ask first whether diameter changes; when it names a density, expect a mass. Those two cues identify most question types.