MECH60561 Chap.3 Beam Elements and Distributed Loads
Beam Elements and Distributed Loads
Beam Elements and Distributed Loads extends interpolation to bending, where each node carries transverse displacement and rotation. Curvature links the displacement field to bending moment, while the element stiffness couples translations and rotations with different powers of length.
Distributed loading is converted into equivalent nodal forces and moments using the same interpolation, then checked by total force and moment. Cantilever benchmarks provide independent scale and direction controls for finite element results.
Release conditions, section-property units and deformation sketches are treated as modelling choices, because each can change the apparent stiffness without altering the matrix-solving procedure. Force and moment checks expose shortcuts that preserve one resultant while losing the bending work.
What this chapter covers
- 01
Beam degrees of freedom
- 02
Cubic displacement interpolation
- 03
Rotation and curvature
- 04
Flexural rigidity
- 05
Equivalent nodal actions
- 06
Cantilever benchmarks
- 07
Bending model diagnosis
Worked example · free
Check a cantilever tip response
- 2Calculate flexural rigidity and preserve the fourth-power length unit in I.
- 4Use the stated benchmark relations for tip displacement and rotation.
- 4Recover shear and moment at the fixed end and check equilibrium.
Key terms
- Flexural rigidity
- The product of elastic modulus and second moment of area governing bending resistance.
- Curvature
- The rate at which beam rotation changes along the member.
- Equivalent nodal action
- A nodal force and moment pattern that represents the work of a distributed load.
Beam Elements and Distributed Loads FAQ
Why does a beam node need rotation?
Bending response depends on both transverse displacement and slope. Sharing displacement and rotation across connected beam elements gives the centreline continuity required by the beam theory used here. A hinge or release changes that transfer and must be modelled explicitly.
How should a distributed beam load be checked?
Sum the equivalent nodal forces and compare them with the area under the load. Then take moments about a common point, including both nodal-force moments and nodal moments. Preserving only total force is insufficient for a bending element.
What can make a beam model too stiff?
Over-constraint, an unsuitable low-order formulation, poor element quality, incorrect section properties or inconsistent units can all suppress displacement. Shear locking is a specific approximation mechanism, so diagnose it with a benchmark and a controlled formulation or refinement comparison.
Exam move
Start each beam problem with a deformation sketch and the nodal degree order. Connect displacement, rotation, curvature, moment and shear as successive derivatives or constitutive steps. Use a simple cantilever to practise dimensional consistency, especially the fourth-power unit in the second moment of area.
Compare a finite element tip displacement with a matching beam benchmark and recover the fixed-end reactions as an independent check. For distributed loads, write the load function and derive or apply the consistent nodal vector, then verify force and moment resultants. Practise symmetric and linearly varying load patterns so the nodal-action direction becomes intuitive.
Review how releases alter moment transfer and why a fully fixed rotation is not interchangeable with a pin. When a model appears too stiff, separate material or section data, support conditions, mesh quality and interpolation issues. Keep an error log for rotational signs, length powers, mixed units and missing nodal moments.
Finish every answer by naming the theory boundary, such as slender geometry, small displacement and linear material response. Build a benchmark sheet around direction and scaling rather than isolated coefficients. Under the same tip load, cantilever displacement scales with the cube of length and inversely with flexural rigidity. Rotation scales with length squared.
Write those directions next to the formulas and use them to predict the effect of every changed input before calculating. Add fixed-end shear and moment so the benchmark checks equilibrium as well as movement. Practise converting section dimensions into the correct second moment rather than treating I as a supplied decoration.
A millimetre-to-metre mistake enters to the fourth power in I and can overwhelm otherwise correct matrix work. Keep E and I in a compatible system, and state the resulting units of EI. For a beam element matrix, label translational and rotational rows explicitly because their coefficients do not share the same dimensions before multiplication by their different degrees.
Work one distributed-load example by integrating the shape functions. Then check the sum of vertical nodal actions and their moment about the left node. Repeat with a triangular load so an automatic equal split no longer works. If the nodal vector includes end moments, explain how they help preserve virtual work. Study releases by sketching what can rotate and which moment transfer disappears.
Compare a pin with a fully fixed end and predict how the deflected shape changes. For suspected locking, keep the physical model unchanged and compare element order, aspect ratio or formulation against a trusted bending response. Do not call every low displacement locking until material, section and support data are checked.
Finish timed practice with a sentence linking the computed deformation to the beam assumption and naming the local behaviour a one-dimensional model cannot resolve.