BENG0003 Chap.4 Upstream Processing and Bioreactor Operation
Upstream Processing and Bioreactor Operation
Upstream Processing and Bioreactor Operation covers the Week 9 material on growing cells to a dense, productive culture. It starts with the two-mark definition of upstream processing and the five steps from medium preparation, sterilisation and inoculation to maintaining growth through a seed train and harvesting. Planar culture vessels are weighed against their limits for large cell lots.
The chapter then sorts bioreactors by how they mix: stirred tanks with axial, radial or mixed-flow impellers, pneumatic bubble columns and airlift reactors, and hydraulic packed bed, fluidised bed and hollow fibre designs, with a decision tree for adherent and suspension cells and the role of microcarriers.
Operating modes follow, with cell and glucose curves for batch and fed-batch culture, the steady state of a chemostat and the high densities of perfusion, plus the revision table of advantages and disadvantages. Sterilisation by steam and 0.2 µm filtration is linked to the reasons contamination matters.
The final pages explain why scale-up is not simply a bigger pot: mixing times stretch from under 5 s to over 50 s, gradients form around surface feeds, and scale-out and scale-down models offer alternatives.
What this chapter covers
- 01
Definition and five steps of upstream processing
- 02
Planar culture vessels and their limits
- 03
Stirred tank, pneumatic and hydraulic bioreactors
- 04
Impeller flow patterns and microcarriers for adherent cells
- 05
Batch, fed-batch, continuous and perfusion operation
- 06
Seed trains and expansion time from a single vial
- 07
Sterilisation methods and contamination control
- 08
Scale-up gradients, feed position, scale-out and scale-down
Worked example · free
Compare batch and fed-batch cell and glucose curves
- 1Batch final cells = 0.4 g/L + 0.5 g/g × 10 g/L = 5.4 g/L, after which growth stops at a plateau.
- 2Batch growth factor = 5.4 / 0.4 = 13.5, so doublings = log2(13.5) = 3.75 and glucose runs out at 3.75 × 2 h = 7.51 h.
- 1Fed-batch cells when the initial glucose is used = 0.4 + 0.5 × 4 = 2.4 g/L; 2.4 / 0.4 = 6 gives log2(6) = 2.58 doublings, so the feed begins at 2.58 × 2 h = 5.17 h.
- 1After the switch cells rise by 0.5 × 1.2 = 0.6 g/L per hour for 16 h less 5.17 h = 10.83 h, adding 6.50 g/L, so cells reach 2.4 + 6.50 = 8.90 g/L at 16 h.
- 1Batch: exponential cell rise to a 5.4 g/L plateau while glucose falls to zero. Fed-batch: the same exponential start, then a straight-line rise past the batch plateau while glucose stays near zero.
Key terms
- Seed train
- A series of progressively larger culture vessels used to build cell numbers from one vial up to production scale.
- Microcarrier
- A small, light bead, slightly denser than medium, that gives anchorage-dependent cells a surface inside a stirred vessel.
- Airlift reactor
- Pneumatic vessel in which sparged gas lifts liquid up a riser and bubble-free liquid sinks back through a downcomer.
- Perfusion culture
- Operation where fresh medium flows continuously through the vessel while a separator keeps the cells inside.
- Scale-down model
- Small replica of a manufacturing step built to reproduce its large-scale behaviour for troubleshooting and studies.
Upstream Processing and Bioreactor Operation FAQ
What is upstream processing in a bioprocess?
Upstream processing is the first part of a bioprocess. It covers preparing a medium suited to the cell type, sterilising equipment and reagents, sourcing cells from a frozen vial, and growing them through flasks and progressively larger bioreactors, often as a seed train, until the culture is ready for harvest and handover to downstream processing.
Which bioreactor is best for adherent mammalian cells?
Anchorage-dependent cells need a surface, so options include a stirred tank with microcarriers, a packed or fluidised bed and a hollow fibre bioreactor. A good exam answer lists these, picks one with justified strengths and weaknesses, and states how it mixes, for example impeller agitation in the stirred tank or medium recirculation in hydraulic designs.
Which impeller should I choose for CHO cells?
Choose a gentle design because mammalian cells are fragile. A marine impeller gives axial flow with gentle mixing, and a pitched or angled blade gives combined axial and radial flow that is still gentle. Radial-flow impellers are better kept for robust, high-density bacterial, yeast or fungal cultures.
What are the advantages of fed-batch over batch culture?
Fed-batch keeps conditions controlled and reaches higher cell densities because nutrients are added after the batch start instead of all at once, which avoids exhausting or overloading the culture. It shares some problems of continuous operation, but less severely. Batch culture is versatile with low contamination risk yet suffers from labour cost and idle time.
Why is scaling up a bioreactor difficult?
Mixing slows dramatically as vessels grow, from below roughly 5 s in 1 to 20 L vessels to above roughly 50 s beyond that, so pockets of high and low glucose and pH appear. Fast-growing bacteria also demand more oxygen and release more heat. Poor scale-up reduces yield, capacity and product quality and can cause genetic instability.
Exam move
Start with the two-mark definition, because it opens many papers: rehearse a version that names fermentation, cell sourcing, sterilisation and media preparation, then traces the cells from a frozen vial through flasks into bioreactors by way of a seed train.
Next, redraw the bioreactor decision tree from memory and attach one advantage, one limitation and the mixing mechanism to each option, since the adherent-reactor question rewards exactly that pattern. Practise the operating-mode sketch with cells and substrate for batch, fed-batch and continuous culture on one set of axes, and learn the pros and cons table row by row.
For scale-up, memorise the two mixing-time bands and explain how surface feeding creates gradients and what moving the feed to the impeller achieves. Finally, rework the seed-train doubling calculation with your own numbers so the logarithm step becomes automatic.