The University of Hong Kong · FACULTY OF ENGINEERING

CIVL2102 Chap.10 Rock Slopes and Engineering Works

- one subject, every graph, every model, every mark
6 Chapters3-page Bible
Our own words - no uploaded lecturer files
Updated for this semester
Chapter 10 of 10 · CIVL2102

Rock Slopes and Engineering Works

Mechanism selection starts with structure

Plane, wedge and toppling failures depend strongly on discontinuity orientation relative to the slope face. Circular failure becomes more relevant in heavily fractured material without a dominant structural pattern. Mapping and stereonet screening therefore precede equilibrium.

A factor of safety belongs to a stated moving block and release surface, not to a slope image in general.

Forces must match the free body

For a dry plane block, weight resolves into driving and normal components. Cohesion acts over contact area, while friction depends on effective normal force. Water pressure can act along the plane or in a tension crack.

A rock bolt adds a directed force that may increase normal compression as well as provide restraint. Every physical change requires a new equilibrium rather than a reused result.

Engineering geology selects the response

Drainage targets pressure, scaling removes loose blocks, bolts cross release surfaces and mesh contains smaller falls. Changing geometry alters kinematics.

The same ground model informs foundations, tunnels, dams and reclamation: variable rockhead changes founding options, fault zones affect inflow and support, and weathered profiles affect excavation and bearing. The final answer should name the observation that would change the design.

In this chapter

What this chapter covers

  • 01

    Plane, wedge, toppling and circular failure

  • 02

    Kinematic screening

  • 03

    Slope free-body forces

  • 04

    Water and effective normal force

  • 05

    Rock bolts and drainage

  • 06

    Foundations, tunnels and ground models

Worked example · free

Check a dry plane block

Q [10 marks]. A unit-width block weighs one hundred kN on a plane dipping thirty degrees. Basal area is five square metres, cohesion ten kPa and friction angle twenty-five degrees. Find factor of safety. The mark allocation used here is an AskSia revision aid, not a University assessment scheme.
The four silhouettes relate structure to movement: a single basal plane, an intersecting wedge, steep columns that rotate, or a curved path through broken materThe four silhouettes relate structure to movement: a single basal plane, an intersecting wedge, steep columns that rotate, or a curved path through broken material.Structure selects the possible slope mechanismplanewedgetopplingcircular
The four silhouettes relate structure to movement: a single basal plane, an intersecting wedge, steep columns that rotate, or a curved path through broken material.
  • 3Resolve driving and normal force.
  • 4Calculate cohesion and friction resistance.
  • 3Form the ratio and state the model boundary.
Driving force is 100 sin30 degrees = 50.0 kN. Normal force is 100 cos30 degrees = 86.6 kN. Cohesion contributes 10 kN/m² × 5 m² = 50.0 kN and friction contributes 86.6 tan25 degrees = 40.4 kN. Factor of safety is 90.4/50.0 = 1.81 for the stated dry, continuous plane and unit width.
Sia tip — Draw water and support forces before adding them. Their direction decides whether they change driving force, normal force or both.
Glossary

Key terms

Plane Failure
Sliding of a block along one suitably oriented release plane.
Wedge Failure
Movement of a block along the intersection of two discontinuity planes.
Toppling
Forward rotation of steep blocks separated by discontinuities.
Circular Failure
Curved movement through material without one dominant planar release surface.
Rock Bolt
A reinforcement element crossing potential release surfaces to add restraint.
Uplift
Water force reducing effective normal contact across a potential sliding plane.
FAQ

Rock Slopes and Engineering Works FAQ

How do I choose a rock-slope failure mode?

Use discontinuity and face geometry first. A single daylighting plane suggests plane sliding, two intersecting planes may form a wedge, steep columns may topple and heavily fractured material may behave through a circular mechanism. Then test resistance.

Why is drainage often the first response?

Where water pressure is materially reducing effective normal force, drainage targets the cause of lost frictional resistance. Reinforcement may still be required, but adding support while leaving avoidable pressure can be less efficient and harder to verify.

How does the same ground model help foundations and tunnels?

It carries material boundaries, weathering, structures and groundwater into different decisions. Foundations use it for founding level and variability, while tunnels use it for stress redistribution, support demand and inflow. The observations remain shared even when analyses differ.

Study strategy

Exam move

For every slope sketch, name the moving mass and release surfaces before writing forces. Use a stereonet statement to justify the mechanism, then draw weight, normal force, water and support. After the calculation, add one monitoring or construction observation that would test the assumed mechanism. Repeat the same ground model for a foundation and tunnel decision. Organise slope revision by mechanism rather than by formula.

For plane failure, identify a continuous daylighting surface and resolve the block weight parallel and normal to it. For a wedge, define the two release planes and the intersection direction. For toppling, describe the steep block geometry and rotation. For circular failure, justify why the fractured mass can be treated without one dominant planar control. Only after that screen should you select equilibrium equations.

Draw water pressure where it acts and show whether a bolt changes normal compression, driving force, or both. Test each result with limiting cases: zero water, zero cohesion, a flatter plane, or support aligned differently. A factor of safety should be accompanied by the assumed unit width, contact area, parameter source, and mechanism.

Match stabilisation to cause: drainage reduces pressure, scaling removes loose blocks, bolts cross release surfaces, mesh contains falls, and geometry changes can remove kinematic freedom. Extend the same ground model beyond slopes.

For a foundation, ask about variable rockhead, bearing material, and deformation; for a tunnel, ask about fault zones, inflow, stress redistribution, and support; for reclamation or dams, ask how deposits and permeability affect the system. Finish each case with an observational test during investigation or construction.

A recommendation is strongest when it says what evidence would confirm the mechanism and what contrary evidence would trigger a different design response.

A+Everything unlocked
Unlocks this Bible + all 52 of your subjects at The University of Hong Kong, plus 1,000+ more Bibles across the AskSia library.
Sia - your CIVL2102 tutor, unlimited, worked the way the exam marks it
The full 3-page Bible + practice bank with worked solutions
Chrome extension - sync your LMS so Sia knows your deadlines
Bilingual EN / Chinese on every Bible and every Sia answer
$0.99 Trial
30-day money-back · cancel in one tap · how it works