The University of Hong Kong · FACULTY OF ENGINEERING

CIVL2102 Chap.9 Failure Criteria and Water Effects

- one subject, every graph, every model, every mark
6 Chapters3-page Bible
Our own words - no uploaded lecturer files
Updated for this semester
Chapter 9 of 10 · CIVL2102

Failure Criteria and Water Effects

A criterion compares a stress state with a boundary

The Mohr-Coulomb criterion represents shear resistance as cohesion plus effective normal stress multiplied by the tangent of friction angle. In Mohr space, critical circles touch a linear envelope.

Cohesion is the intercept, friction angle controls the slope and a tensile cutoff prevents the compression-based line from implying unrealistic tensile strength.

Demand and resistance are different lines

The applied shear stress or transformed stress state is demand. The criterion supplies available resistance from parameters and effective normal stress. Mixing them inside one equation hides the comparison.

A factor of safety or explicit inequality should follow after both are calculated. Confinement matters, so major principal stress alone does not describe failure under a multiaxial state.

Water changes effective stress

Pore pressure is subtracted from total normal stress. Equal pressure on the principal stresses shifts the effective Mohr circle toward lower normal stress without changing its radius.

Frictional resistance falls even if the external load is unchanged. Nonlinear rock response motivates empirical criteria such as Hoek-Brown, while equivalent linear parameters remain tied to a chosen stress range and material scale.

In this chapter

What this chapter covers

  • 01

    Mohr-Coulomb envelope

  • 02

    Cohesion and friction angle

  • 03

    Tensile cutoff

  • 04

    Demand against resistance

  • 05

    Pore pressure and effective stress

  • 06

    Hoek-Brown and fitting range

Worked example · free

Quantify a pore-pressure effect

Q [9 marks]. A plane carries total normal stress six MPa. Cohesion is two MPa and friction angle thirty degrees. Compare resistance when dry and when pore pressure is three MPa. The mark allocation used here is an AskSia revision aid, not a University assessment scheme.
The blue total-stress circle moves left by the pore pressure to become the red effective-stress circle, reducing normal confinement without changing circle radiThe blue total-stress circle moves left by the pore pressure to become the red effective-stress circle, reducing normal confinement without changing circle radius.Water shifts effective stress toward the failure envelopeτ = c + σ tan φsubtract pore pressure
The blue total-stress circle moves left by the pore pressure to become the red effective-stress circle, reducing normal confinement without changing circle radius.
  • 3Calculate dry resistance.
  • 3Convert total to effective normal stress.
  • 3Calculate wet resistance and interpret the change.
Dry resistance is 2 + 6 tan30 degrees = 5.46 MPa. With pore pressure three MPa, effective normal stress is three MPa and resistance becomes 2 + 3 tan30 degrees = 3.73 MPa. Resistance falls by 1.73 MPa without any change in total normal stress. Applied shear demand must still be compared before failure is declared.
Sia tip — Put total stress, pore pressure and effective stress on separate lines so the water effect cannot disappear.
Glossary

Key terms

Cohesion
The zero-normal-stress intercept of a linear Mohr-Coulomb envelope.
Friction Angle
The parameter controlling the envelope slope with effective normal stress.
Tensile Cutoff
A limit preventing a compression criterion from overstating tensile strength.
Effective Stress
Total stress minus pore pressure for the solid skeleton response.
Tangency
Contact between a critical Mohr circle and the failure envelope.
Hoek-Brown
An empirical nonlinear failure criterion used for rock and rock masses.
FAQ

Failure Criteria and Water Effects FAQ

Why does water reduce shear resistance?

Pore pressure carries part of the total normal stress, leaving less effective compression across the potential failure plane. The frictional part of resistance therefore falls. The external load can remain unchanged while the effective state moves toward failure.

Why is a tensile cutoff needed?

A straight envelope fitted mainly to compressive states can imply unrealistic tensile capacity when extended left. The cutoff represents the much lower tensile strength and prevents the model from using its compression fit outside a defensible domain.

Are cohesion and friction angle fixed rock constants?

They describe a fitted material, scale and stress range. Values from intact specimens may not represent a discontinuity or jointed mass, and equivalent linear values derived from a nonlinear criterion depend on the confinement interval selected.

What is the fastest effective-stress audit?

Write total normal stress, pore pressure and effective normal stress on separate lines before calculating frictional resistance. Then predict how the Mohr circle or sliding resistance should change. If higher pore pressure increases friction, leaves effective stress unchanged or alters circle radius under equal pressure, revisit the signs and model.

Study strategy

Exam move

Draw the envelope and one circle, then practise three changes separately: greater confinement, greater shear demand and greater pore pressure. Say how the diagram moves before calculating. Label whether parameters describe intact rock, a discontinuity or a mass. Use one line each for demand, resistance and verdict. Begin every problem by identifying the material scale and stress convention.

Cohesion and friction angle for an intact specimen, a filled joint, and an equivalent rock mass are not interchangeable even when the equation has the same form. Write effective normal stress before resistance so that pore pressure cannot disappear inside substitution. On a shear-plane calculation, keep applied demand and available resistance on separate lines and form a ratio or inequality only at the end.

On a Mohr diagram, draw total and effective states in different colours. Equal pore pressure shifts the circle left without changing its radius; changing differential stress alters the radius. Practise predicting those movements before using numbers. Add a tensile cutoff where the linear compression envelope would imply unrealistic tension.

For nonlinear criteria, state the parameter set and stress range rather than converting automatically to one global cohesion and friction angle. Use sensitivity drills by changing water pressure, confinement, or one strength parameter at a time and explaining which part of the diagram changes.

Then connect the mathematical result to a mechanism: a potential sliding plane, confined intact rock around an excavation, or a fractured mass. Review errors by asking whether the chosen criterion describes the observed failure mode and whether the parameters come from compatible tests.

Finish with one observation or measurement that could revise the verdict, such as joint filling, drainage response, confinement, or scale-dependent strength.

A+Everything unlocked
Unlocks this Bible + all 52 of your subjects at The University of Hong Kong, plus 1,000+ more Bibles across the AskSia library.
Sia - your CIVL2102 tutor, unlimited, worked the way the exam marks it
The full 3-page Bible + practice bank with worked solutions
Chrome extension - sync your LMS so Sia knows your deadlines
Bilingual EN / Chinese on every Bible and every Sia answer
$0.99 Trial
30-day money-back · cancel in one tap · how it works