The University of Hong Kong · FACULTY OF ELECTRICAL ENGINEERING

ELEC6103 Chap.8 System Noise, G/T and Carrier-to-Noise Ratio

- one subject, every graph, every model, every mark
7 Chapters4-page Bible
Our own words - no uploaded lecturer files
Updated for this semester
Chapter 8 of 11 · ELEC6103

System Noise, G/T and Carrier-to-Noise Ratio

Received power needs a noise reference

Knowing that a carrier arrives at around minus 116 dBW says nothing about link quality until the noise accompanying it is known. Thermal noise has a flat spectrum whose density is kT watts per hertz, and integrating it over a bandwidth B gives a noise power of kTB. Boltzmann's constant, 1.38 × 10−23 J/K, becomes −228.6 dBW/K/Hz in decibel form.

The carrier-to-noise ratio in decibels is then simply received power minus noise power; because noise in dBW is a large negative number, subtracting it raises the ratio.

Bandwidth and system temperature

Bandwidth affects the ratio only through noise: twice the bandwidth admits twice the noise and costs 3 dB.

The tutorial tables make this vivid, since a low-orbit link 50 dB weaker than a C band uplink still closes on a 20 kHz channel. The system noise temperature of a receiver chain adds the antenna and first amplifier temperatures, then each later stage divided by the gain in front of it.

A high-gain low noise amplifier mounted at the antenna therefore hides a noisy mixer almost completely, so that first stage is where the design money should go.

G/T as the receive figure of merit

In the revised Lecture 7 formula for C/N, receive gain and system temperature never appear separately but always as a single quotient, so a single dB/K number captures how good a receiving station is.

A larger dish improves it twice, once through gain on the carrier and once through the ratio itself. The sample Ku band budget shows a 1.8 m remote terminal at 22.9 dB/K and a 1.2 m terminal at 19.2 dB/K, with downlink C/N falling to match.

Combining the two halves of a bent-pipe link

A bent-pipe transponder amplifies uplink noise with the carrier, so the noise of both links accumulates.

The combination must be done with linear ratios: the reciprocal of the overall C/N is the sum of the uplink and downlink reciprocals. The result always sits below the weaker link, and when the two differ by more than 25 dB the tutorial lets you simply take the lower value.

Interference is added the same way as C/I to give C/(N+I).

Rain hits twice

In the direct broadcast tutorial, rain attenuates the carrier by 2 dB and also warms the sky seen by the antenna, lifting system temperature from 110 K to 210 K. The ratio drops by about 4.8 dB, more than the attenuation alone suggests.

In this chapter

What this chapter covers

  • 01

    Thermal noise, kTB and Boltzmann's constant in decibels

  • 02

    Carrier-to-noise ratio as received power minus noise power

  • 03

    How bandwidth trades against C/N

  • 04

    System noise temperature of a cascaded receiver chain

  • 05

    G/T as the figure of merit for a receiving station

  • 06

    Combining uplink and downlink C/N with reciprocals

  • 07

    Rain fade as a loss and a noise increase together

Worked example · free

Overall C/N from a 24 dB uplink and a 16 dB downlink

Q [7 marks]. AskSia-authored practice. A bent-pipe transponder link has an uplink C/N of 24 dB and a downlink C/N of 16 dB. Find the overall C/N, state whether the 25 dB shortcut may be used, and say how far the overall value sits below the downlink alone. The marks shown are an AskSia study allocation, not the University's marking scheme.
The overall carrier-to-noise ratio can never beat the weaker link.The overall carrier-to-noise ratio can never beat the weaker link. The curve combines a fixed 15 dB downlink with a rising uplink; once the uplink is far stronger, the overall value settles just below the downlink line.downlink alone, 15 dBuplink 28: overall 14.8uplink C/N, dBoverall C/N, dB
The overall carrier-to-noise ratio can never beat the weaker link. The curve combines a fixed 15 dB downlink with a rising uplink; once the uplink is far stronger, the overall value settles just below the downlink line.
  • 2Convert both ratios from dB to linear values.
  • 2Add the reciprocals: 1/(C/N)o = 1/(C/N)up + 1/(C/N)down.
  • 2Invert the sum and convert the overall ratio back to dB.
  • 1Compare the 8 dB gap with the 25 dB rule and with the downlink value.
In linear terms the uplink is 102.4 = 251.2 and the downlink is 101.6 = 39.8. The reciprocals are 1/251.2 = 0.00398 and 1/39.8 = 0.02512, which sum to 0.02910. Inverting gives an overall ratio of 1 / 0.02910 = 34.4, and 10 log 34.4 = 15.4 dB. The two links differ by only 24 - 16 = 8 dB, well short of 25 dB, so the shortcut of taking the lower value is not allowed here; quoting 16 dB would overstate the link by 0.6 dB. The overall value is 0.6 dB below the downlink, showing that the weaker downlink dominates but the uplink still contributes measurably.
Sia tip — Never add or average the dB figures; convert to linear ratios, add the reciprocals, and only return to dB at the very end.
Glossary

Key terms

Noise Power Spectral Density
The noise power per hertz, N0 = kT, flat across frequency for thermal noise and equal to minus 228.6 dBW/K/Hz plus 10 log T in decibel form.
System Noise Temperature
The single equivalent temperature of a whole receive chain, found by adding antenna and first amplifier temperatures and each later stage divided by the gain preceding it.
G/T
The ratio of receive antenna gain to system noise temperature, quoted in dB/K; it is the receiving station's figure of merit because C/N depends on gain and temperature only through it.
Overall C/N
The end-to-end carrier-to-noise ratio of a bent-pipe link, obtained by adding the linear reciprocals of the uplink and downlink ratios and inverting, never by combining decibel values.
FAQ

System Noise, G/T and Carrier-to-Noise Ratio FAQ

Why does a narrow carrier close a link that a wide one cannot?

Thermal noise grows in direct proportion to the bandwidth the receiver admits, while the carrier power stays the same. Cutting bandwidth from 36 MHz to 20 kHz removes over 32 dB of noise, which is how the low-orbit tutorial link survives even though its carrier arrives over 50 dB weaker than in the geostationary examples. Each halving of bandwidth recovers about 3 dB.

Why is the low noise amplifier placed right at the antenna?

In a cascade, every stage after the first has its noise divided by the gain ahead of it. Putting a high-gain, low-temperature amplifier first means a 1,000 K mixer behind 40 dB of gain contributes only a tenth of a kelvin. Any lossy cable or noisy stage placed before that amplifier would instead add directly to the system temperature and degrade G/T.

Which value of Boltzmann's constant should I use in decibel sums?

The tutorials take k as minus 228.6 dBW/K/Hz and add it when computing noise power, while the revised lecture prints plus 228.5 inside its C/N formulas, where subtracting kT turns the sign positive. Either works if applied consistently. Use 228.6 for agreement with the worked tutorials and write down the convention so a marker can follow each line.

How can I check a commercial link budget printout?

Pick a column and rebuild its totals from its rows. In the sample Ku band budget, an 18.6 dB uplink and 16.3 dB downlink combine by reciprocals to 14.3 dB, matching the printed overall value, and interference then reduces C/(N+I) to 11.7 dB. If a total cannot be reproduced from the listed inputs, the sheet should not be trusted as evidence for a design decision.

Study strategy

Exam move

Start by writing the three noise lines that every tutorial repeats: received power, noise power as minus 228.6 plus 10 log T plus 10 log B, and their difference. Rework the five tutorial links in one table so you can see bandwidth and temperature moving the answer. Practise the cascade formula with an LNA gain of 30 and 40 dB to feel how little the mixer contributes.

Drill the reciprocal combination on three pairs, including one where the links differ by more than 25 dB. Finally take one column of the sample Ku band budget and reproduce its overall C/N, then explain in one sentence why a bigger dish raises G/T.

Working through System Noise, G/T and Carrier-to-Noise Ratio in ELEC6103? Sia is AskSia’s AI Electrical Engineering tutor — ask any ELEC6103 System Noise, G/T and Carrier-to-Noise Ratio question and get a clear, step-by-step explanation grounded in how ELEC6103 is taught and assessed. Read this chapter free, then take your hardest questions to Sia.

A+Everything unlocked
Unlocks this Bible + all 52 of your subjects at The University of Hong Kong, plus 1,000+ more Bibles across the AskSia library.
Sia - your ELEC6103 tutor, unlimited, worked the way the exam marks it
The full 4-page Bible + practice bank with worked solutions
Chrome extension - sync your LMS so Sia knows your deadlines
Bilingual EN / Chinese on every Bible and every Sia answer
$0.99 Trial
30-day money-back · cancel in one tap · how it works