The University of Hong Kong · FACULTY OF ENGINEERING

ENGG1000 Chap.8 Axial Members, Determinacy and Trusses

- one subject, every graph, every model, every mark
8 Chapters4-page Bible
Our own words - no uploaded lecturer files
Updated for this semester
Chapter 8 of 10 · ENGG1000

Axial Members, Determinacy and Trusses

From force to material response

Average axial stress is force divided by area, strain is extension divided by original length, and linear elastic behaviour links them through Young's modulus.

The combined deformation relationship requires consistent units and a member carrying axial load through its centroid.

From external reactions to member forces

Ideal pin-jointed trusses carry axial tension or compression. Whole-structure equilibrium provides reactions. The method of joints progresses through members, while the method of sections exposes selected forces efficiently.

Extra unknowns are redundancies and require compatibility beyond rigid-body equilibrium.

Keep force, stress, strain and extension in sequence

First identify the axial force from equilibrium, then divide by the member area for stress. Use the material modulus to convert stress to strain and multiply strain by original length for extension.

This sequence exposes unit errors: newtons per square millimetre are megapascals, while gigapascals must be converted consistently. Tension and compression signs should remain visible because extensions from several segments combine algebraically.

Separate global and joint equilibrium

On the whole-truss diagram, member forces are internal and cancel, leaving applied loads and support reactions.

After reactions are known, isolating a joint exposes member forces along their axes. Assume unknown members pull away from the joint as tension; a negative answer then means compression.

The same two-force member appears with equal and opposite end actions, connecting the local joint solutions into one globally consistent structure.

Select joints or sections from the requested output

The method of joints is systematic when many member forces are needed and begins at a joint with no more than two unknowns.

The method of sections is efficient for selected forces: pass a cut through the target and no more than three independent unknown members in a planar truss.

Choose a moment point at the intersection of two cut-force lines to isolate the third whenever the geometry permits.

Use counting only as a first determinacy screen

Comparing members, reactions and joints can indicate a determinate candidate, redundancy or likely instability, but geometry still controls whether the equilibrium equations are independent.

A rectangle without suitable triangulation may deform as a mechanism. When redundancies remain, equilibrium alone cannot determine the force split; deformation compatibility and material stiffness add the missing information. State the structural idealisation before applying any memorised count.

In this chapter

What this chapter covers

  • 01

    Axial force

  • 02

    Stress and strain

  • 03

    Hooke's law

  • 04

    Young's modulus

  • 05

    Determinacy and redundancy

  • 06

    Method of joints

  • 07

    Method of sections

  • 08

    Zero-force members

Worked example · free

Calculate elastic extension

Q [8 marks]. AskSia-authored practice. A 1.5 m steel bar of area 250 square millimetres carries 30 kN tension. Take E as 200 GPa. The marks shown are an AskSia study allocation, not the University's marking scheme.
The route separates global and local equilibrium.The route separates global and local equilibrium. Whole-structure reactions are found first, after which the method of joints reveals every member or the method of sections targets a selected set.Solve external reactions before choosing joints or sectionsWhole-truss FBDReactionsAll members: jointsSelected members:cutAt joints, tension points outward;negative means compression.
The route separates global and local equilibrium. Whole-structure reactions are found first, after which the method of joints reveals every member or the method of sections targets a selected set.
  • 2Find stress.
  • 3Find strain.
  • 3Find extension and check directly.
Stress is 30,000/250 = 120 MPa. With E = 200,000 MPa, strain is 120/200,000 = 0.0006. The original length is 1,500 mm, so extension is 0.0006 times 1,500 = 0.90 mm. The direct FL over AE calculation confirms 0.90 mm.
Sia tip — Use newtons, millimetres and megapascals together so area and modulus conversions stay visible.
Glossary

Key terms

Axial Stress
Axial force divided by cross-sectional area.
Normal Strain
Axial deformation divided by original length.
Young's Modulus
The elastic stress-to-strain ratio in the linear range.
Redundancy
An extra unknown force beyond what equilibrium equations can determine.
Method Of Joints
Truss analysis by force equilibrium at individual joints.
Method Of Sections
Truss analysis by cutting selected members and balancing one side.
FAQ

Axial Members, Determinacy and Trusses FAQ

What does a negative truss member force mean?

If unknown member arrows were assumed outward from a joint, the assumption represents tension. A negative solved value means the actual force points inward and the member is in compression. State the member state rather than leaving a bare negative sign.

When is the method of sections preferable?

Use it when only a few member forces are required. Cut through the target members and no more than three independent unknown member forces in a planar truss, then isolate the side with simpler loading and reactions.

Does a zero-force member serve no purpose?

It carries zero axial force for the stated loading case, but it can stabilise geometry, maintain shape during construction or carry force under another load case. The label describes one analysis condition, not the member's general value.

Study strategy

Exam move

Separate the structural and material scales. Solve whole-structure reactions, then joint or section equilibrium, and only then calculate stress or deformation in a named member. Practise tension-positive arrows consistently and use a final unused joint as an equilibrium check after the main solution.

Build a route card that asks whether all member forces or only selected forces are required, then directs you to joints or a section. On stepped axial members, tabulate force, length, area, modulus and signed deformation for each segment before summing. For trusses, mark zero-force candidates but verify that the joint conditions apply.

After classifying determinacy by count, inspect geometry separately and explain whether triangulation and restraint directions actually prevent mechanism motion.

A+Everything unlocked
Unlocks this Bible + all 52 of your subjects at The University of Hong Kong, plus 1,000+ more Bibles across the AskSia library.
Sia - your ENGG1000 tutor, unlimited, worked the way the exam marks it
The full 4-page Bible + practice bank with worked solutions
Chrome extension - sync your LMS so Sia knows your deadlines
Bilingual EN / Chinese on every Bible and every Sia answer
$0.99 Trial
30-day money-back · cancel in one tap · how it works