The University of Manchester · FACULTY OF ENGINEERING

CIVL13001 Chap.7 Beam Stress and Section Properties

- one subject, every graph, every model, every mark
7 Chapters3-page Bible
Our own words - no uploaded lecturer files
Updated for this semester
Chapter 7 of 8 · CIVL13001

Beam Stress and Section Properties

Beam Stress and Section Properties explains how bending moment creates a linear elastic stress distribution across a cross-section. Stress is zero at the neutral axis and reaches its largest magnitude at an outer fibre. Second moment of area measures how area is distributed about an axis, while section modulus combines that geometry with the extreme-fibre distance.

Composite sections require a common centroid and parallel-axis transfers.

The flexure relation depends on the bending axis, the moment sign and the distance of the evaluated fibre from the neutral axis. Second moment of area is not a material property and cannot be quoted without its axis.

For rectangles, the depth measured perpendicular to that axis is cubed, which explains the strong benefit of distributing area away from the neutral axis. Composite sections are reduced to signed component areas, a common centroid and transferred component moments using A d squared. Holes are subtracted consistently.

Stress values are attached to named fibres and interpreted as tension or compression, while a section-modulus route provides an independent extreme-fibre check.

In this chapter

What this chapter covers

  • 01

    Plane sections

  • 02

    Neutral axis

  • 03

    Bending stress

  • 04

    Second moment of area

  • 05

    Parallel-axis theorem

  • 06

    Composite sections

  • 07

    Section modulus

Worked example · free

Check a rectangular beam in bending

Q [7 marks]. A 90 mm by 240 mm rectangle carries 18 kNm about its centroidal horizontal axis. Find I and extreme stress. The marks shown here are original study guidance and not an official University assessment scheme.
The rectangular section has zero bending stress at its neutral axis and linearly increasing compression and tension toward the opposite outer fibres where magniThe rectangular section has zero bending stress at its neutral axis and linearly increasing compression and tension toward the opposite outer fibres where magnitudes are largest.neutral axiscompressiontension0rectangular cross-sectionlinear stress distribution
The rectangular section has zero bending stress at its neutral axis and linearly increasing compression and tension toward the opposite outer fibres where magnitudes are largest.
  • 3Use I = bh cubed over 12 to obtain 103,680,000 mm to the fourth.
  • 2Convert moment to 18,000,000 Nmm and use an extreme-fibre distance of 120 mm.
  • 2My over I gives 20.83 MPa at each outer face, with opposite tension and compression signs.
The second moment is 103,680,000 mm to the fourth and the extreme stress magnitude is 20.83 MPa. The practice marks are not official.
Sia tip — Write the bending axis beside I and convert moment units before substituting into the flexure relation.
Glossary

Key terms

Neutral axis
The cross-section line at which elastic bending strain and stress are zero.
Parallel-axis theorem
A relation that transfers a centroidal second moment to a parallel axis using area times offset squared.
Section modulus
Second moment of area divided by the extreme-fibre distance for the selected bending axis.
FAQ

Beam Stress and Section Properties FAQ

Why does beam depth matter so much?

For a rectangular section, second moment contains the cube of depth about the relevant axis. Moving material farther from the neutral axis therefore increases bending stiffness and reduces stress rapidly for the same moment.

Why must I name the axis for I?

Second moment of area changes with both axis orientation and position. The same cross-section can be strong about one centroidal axis and weak about the perpendicular axis, so an unlabeled value is ambiguous.

How are holes handled in a composite section?

Locate the common centroid using signed areas, then subtract the hole's centroidal second moment and its parallel-axis contribution. The removed area must remain negative throughout the section calculation.

Study strategy

Exam move

Pair every beam-stress problem with a cross-section sketch. Mark the bending axis, locate the centroid and show the neutral axis before calculating I. For simple rectangles, identify which dimension is cubed and predict how rotating the section changes stiffness. For composite sections, make a table of signed area, centroid position, local centroidal I and A d squared, then sum about one common axis.

Convert bending moment into units consistent with the section dimensions. Calculate stress at named fibres and attach tension or compression according to the selected moment convention. Use section modulus as a second route for the extreme value. Practise comparing sections with equal area but different material distribution so the geometric meaning of I becomes intuitive.

Record errors under wrong axis, total depth used as y, omitted parallel-axis term, hole sign and moment conversion. End with a distribution sketch that is zero at the neutral axis and reaches extrema at the outer fibres. Develop geometric intuition with cut-paper sections or quick scale sketches. Move the same area away from a trial axis and predict whether I rises before evaluating any formula.

Rotate rectangles and compare strong-axis with weak-axis behaviour. For an I-shaped section, calculate the centroid from signed areas first, then keep each flange and web row separate in the parallel-axis table. Recompute the total using an outer rectangle minus inner voids where that alternative is available. Agreement between additive and subtractive routes is a powerful check.

Pair every maximum stress with the actual fibre coordinate and the selected moment sign. On an asymmetric section, calculate both extreme distances because the tension and compression magnitudes need not match. Add one section-modulus comparison to see how tables can speed selection without erasing the underlying axis.

Keep dimensions in millimetres through I, y and moment conversion so stress emerges in N per square millimetre. A result with length-squared or length-to-the-fourth units has not completed the flexure calculation. Finish by distinguishing bending stress from shear stress at the neutral axis.

A+Everything unlocked
Unlocks this Bible + all 41 of your subjects at The University of Manchester, plus 1,000+ more Bibles across the AskSia library.
Sia - your CIVL13001 tutor, unlimited, worked the way the exam marks it
The full 3-page Bible + practice bank with worked solutions
Chrome extension - sync your LMS so Sia knows your deadlines
Bilingual EN / Chinese on every Bible and every Sia answer
$0.99 Trial
30-day money-back · cancel in one tap · how it works