The University of Manchester · FACULTY OF ENGINEERING

CIVL13001 Chap.6 Material Behaviour and Axial Deformation

- one subject, every graph, every model, every mark
7 Chapters3-page Bible
Our own words - no uploaded lecturer files
Updated for this semester
Chapter 6 of 8 · CIVL13001

Material Behaviour and Axial Deformation

Material Behaviour and Axial Deformation converts force and extension into stress and strain so specimens of different size can be compared. Young's modulus is the linear elastic stress-strain slope, while yielding and plastic response describe different material limits.

Axial extension depends on force, length, area and modulus, and Poisson's ratio connects axial strain with lateral response under stated conditions.

Normalising by area and original length separates specimen geometry from the material response measured in an axial test. Stress retains force-per-area units, strain is dimensionless, and their elastic ratio carries stress units.

A prismatic member under constant axial force extends by force times length divided by area and modulus, but a stepped or varying member must be handled segment by segment or through integration. Unit families are therefore part of the solution: newtons, millimetres, square millimetres and N per square millimetre close directly to millimetres of extension.

A second calculation through stress, strain and original length should reproduce the direct formula and reveal conversion errors.

In this chapter

What this chapter covers

  • 01

    Direct stress

  • 02

    Engineering strain

  • 03

    Young's modulus

  • 04

    Elastic response

  • 05

    Plastic response

  • 06

    Poisson's ratio

  • 07

    Axial extension

Worked example · free

Extend a rectangular steel tie

Q [7 marks]. A 2.4 m steel tie is 30 mm by 12 mm, carries 72 kN tension and has E = 200 GPa. Find stress, strain and extension. The marks shown here are original study guidance and not an official University assessment scheme.
The stress-strain curve begins with a linear elastic slope equal to Young’s modulus, then departs near yield, continues through plastic deformation and ends at The stress-strain curve begins with a linear elastic slope equal to Young’s modulus, then departs near yield, continues through plastic deformation and ends at fracture.strainstresselastic slope Eyield regionplastic responsefracture
The stress-strain curve begins with a linear elastic slope equal to Young’s modulus, then departs near yield, continues through plastic deformation and ends at fracture.
  • 2Area is 360 mm squared and stress is 72,000 divided by 360, or 200 MPa.
  • 2Strain is 200 divided by 200,000, or 0.001 after converting E to N per square millimetre.
  • 3Extension is 0.001 multiplied by 2,400 mm, giving 2.4 mm elongation.
Stress is 200 MPa, strain is 0.001 and the tie extends by 2.4 mm in tension. The marks are original practice guidance.
Sia tip — Put force, length, area and modulus into one unit family before evaluating the axial formula.
Glossary

Key terms

Elastic range
The response range in which deformation is recovered when the action is removed.
Yield stress
A stress associated with the onset of significant permanent deformation under the chosen definition.
Poisson's ratio
The negative ratio of lateral strain to axial strain in a uniaxial loading condition.
FAQ

Material Behaviour and Axial Deformation FAQ

Why use stress instead of force alone?

Stress divides force by area, allowing the intensity of axial action to be compared between specimens with different cross-sections. Force alone cannot distinguish the effect of carrying the same load through different areas.

Why use strain instead of extension alone?

Strain divides length change by original length, so deformation can be compared between members of different length. The same extension represents different material response in a short and a long specimen.

How can I catch unit errors in extension?

Use newtons, millimetres, square millimetres and N per square millimetre together, or another coherent family. Then confirm strain equals both stress divided by modulus and extension divided by original length.

Study strategy

Exam move

Build each material problem from a four-column input table for force, length, area and modulus. Convert units before writing formulas. Calculate stress and strain separately, then obtain extension through strain times length and use FL over AE as a second route. Practise proportional changes: doubling force or length doubles extension, while doubling area or modulus halves it under the same linear model.

Add stepped bars by solving each segment with local properties and summing compatible extensions. Read stress-strain curves by feature rather than by shape alone: identify elastic slope, departure from linearity, yield region and final fracture, and do not confuse modulus with strength. Include lateral deformation only after the axial strain is established and use the original lateral dimension.

Keep an error ledger for area, metre-to-millimetre conversion, gigapascal conversion, series segments and sign. State tension or compression and the model conditions in the final sentence. Create a unit ladder that connects pascals, megapascals and gigapascals to N per square metre and N per square millimetre. Reproduce the conversions without a calculator until a factor of one thousand is visually obvious.

Compare two specimens made from the same material but with different area and length, predicting stress and extension before solving. Then compare two materials in identical geometry to separate stiffness from strength. For stress-strain plots, annotate what unloading would do in the elastic and plastic regions rather than treating the curve as one monotonic story.

Add a restrained thermal expansion example conceptually to distinguish total strain, free thermal strain and mechanical strain, while using only relations supplied in the question. For Poisson response, sketch axial elongation and lateral contraction with the sign convention visible. Recalculate every axial result through both stress-strain and direct extension routes.

If they disagree, locate the first inconsistent unit or geometry. Finish by estimating the order of magnitude: a normal engineering strain is dimensionless and typically far smaller than one in the elastic examples used here, while extension scales with the original member length.

A+Everything unlocked
Unlocks this Bible + all 41 of your subjects at The University of Manchester, plus 1,000+ more Bibles across the AskSia library.
Sia - your CIVL13001 tutor, unlimited, worked the way the exam marks it
The full 3-page Bible + practice bank with worked solutions
Chrome extension - sync your LMS so Sia knows your deadlines
Bilingual EN / Chinese on every Bible and every Sia answer
$0.99 Trial
30-day money-back · cancel in one tap · how it works