The University of Hong Kong · FACULTY OF ENGINEERING

CIVL2102 Chap.5 Discontinuities and Stereonet Reasoning

- one subject, every graph, every model, every mark
6 Chapters2-page Bible
Our own words - no uploaded lecturer files
Updated for this semester
Chapter 5 of 10 · CIVL2102

Discontinuities and Stereonet Reasoning

A rock mass is not a large intact specimen

Joints, bedding, faults and shear zones divide a rock mass into blocks. Their orientation controls possible movement, spacing and persistence control block size, and roughness, aperture, filling and water influence resistance. A useful log records these properties separately.

Saying that rock is highly fractured does not identify a mechanism or provide parameters for one.

Orientation needs a convention

Strike is horizontal on the plane. Dip is the steepest downward line and must include direction. Two planes with the same strike and dip magnitude can face opposite ways, so leaving dip direction unstated loses the engineering geometry.

On a stereonet a plane is a great circle, a pole is normal to the plane, and two planes intersect along a line.

Kinematic screening is not a stability verdict

A plotted plane or line can be compared with an excavation face to determine whether movement is geometrically possible. Plane sliding may be possible where a discontinuity dips toward and daylights in the face.

A wedge requires the intersection line of two planes to be able to exit. Strength and water still control resistance. The correct conclusion is possible or excluded under the geometry, followed by a separate mechanical check.

In this chapter

What this chapter covers

  • 01

    Intact rock against rock mass

  • 02

    Orientation, spacing and persistence

  • 03

    Roughness, aperture and filling

  • 04

    Strike, dip and dip direction

  • 05

    Great circles, poles and intersection lines

  • 06

    Kinematic possibility against stability

Worked example · free

Screen a slope face

Q [9 marks]. A face dips sixty-five degrees south. A persistent joint set dips forty degrees south, and another set dips seventy degrees east. What should be plotted and concluded first? The mark allocation used here is an AskSia revision aid, not a University assessment scheme.
The two joint sets divide the mass into blocks: closer spacing produces smaller blocks, while persistent traces allow a release surface to extend across the excThe two joint sets divide the mass into blocks: closer spacing produces smaller blocks, while persistent traces allow a release surface to extend across the excavation.Spacing and persistence govern block sizeclose spacingpersistent trace
The two joint sets divide the mass into blocks: closer spacing produces smaller blocks, while persistent traces allow a release surface to extend across the excavation.
  • 3Test the first set for plane daylighting.
  • 3Plot both planes and their intersection line.
  • 3Separate kinematic possibility from resistance.
The south-dipping set is a plane-failure candidate because it dips toward the face and less steeply than the face. Plot both planes as great circles and determine their intersection line to screen a wedge. Either result establishes possible geometry only. Roughness, persistence, filling, cohesion, friction and water must be checked before declaring instability.
Sia tip — Plot first, then use the words possible or excluded. Save stable or unstable for the mechanical comparison.
Glossary

Key terms

Discontinuity
A plane of weakness or separation within a rock mass.
Spacing
The perpendicular distance between adjacent discontinuities of a set.
Persistence
The areal extent of a discontinuity, often estimated from trace length.
Aperture
The separation between opposing discontinuity walls.
Pole
A line normal to a plane, plotted as a point on a stereonet.
Great Circle
The stereographic projection representing all lines within a plane.
FAQ

Discontinuities and Stereonet Reasoning FAQ

Why do spacing and persistence matter separately?

Spacing influences the typical block dimension, while persistence controls whether a potential release surface continues far enough to define a moving block. Close spacing with short traces can behave differently from wider spacing with one continuous surface.

What is the difference between a plane and its pole?

The great circle represents the plane itself. The pole is the line perpendicular to that plane and plots as one point. Pole clusters make joint sets easy to recognise, while great circles are convenient for finding intersections.

Can a stereonet prove that a slope will fail?

No. It can establish whether a plane or intersection line has a compatible movement direction relative to the face. Failure still depends on resistance, water pressure, persistence, block weight and any support. Geometry is a necessary screen, not a complete analysis.

Study strategy

Exam move

Practise the physical meaning before plotting. Hold a card as a plane, identify its strike line, tilt it along true dip and point to the pole. Then plot several sets and describe only the geometry. Add roughness, filling and water in a second pass so that kinematic and mechanical reasoning remain distinct.

Build fluency by converting a plane description into three linked forms: field notation, a hand-held plane orientation, and a stereonet great circle or pole. Check dip direction every time; a correct dip magnitude facing the wrong quadrant represents a different surface. Plot small groups of measurements and decide whether a cluster is a joint set or scattered data before drawing an average.

For each set, keep an adjacent description table for spacing, persistence, roughness, aperture, filling, weathering, and water. This prevents orientation from standing in for engineering condition. Practise plane and wedge screening with a stated excavation face. First give only the kinematic result: possible, excluded, or uncertain. Then add friction, cohesion, persistence, and water to discuss resistance.

For a wedge, identify the intersection line rather than treating either great circle as the movement direction. For toppling, check the relationship between steep discontinuities and the face instead of borrowing plane-sliding language. Use counterexamples as a review tool: draw a discontinuity that is weak but cannot daylight, and another that can daylight but is rough and dry.

Explain why neither geometry nor strength alone proves failure. Finish each problem by translating the plot into a field action, such as mapping trace continuity, checking filling, measuring water, or altering the excavation orientation. A readable stereonet answer should always state what was plotted, what comparison was made, and what conclusion remains conditional.

A+Everything unlocked
Unlocks this Bible + all 52 of your subjects at The University of Hong Kong, plus 1,000+ more Bibles across the AskSia library.
Sia - your CIVL2102 tutor, unlimited, worked the way the exam marks it
The full 2-page Bible + practice bank with worked solutions
Chrome extension - sync your LMS so Sia knows your deadlines
Bilingual EN / Chinese on every Bible and every Sia answer
$0.99 Trial
30-day money-back · cancel in one tap · how it works