The University of Hong Kong · FACULTY OF ENGINEERING

CIVL2102 Chap.6 Stress, Strain and Elastic Response

- one subject, every graph, every model, every mark
6 Chapters2-page Bible
Our own words - no uploaded lecturer files
Updated for this semester
Chapter 6 of 10 · CIVL2102

Stress, Strain and Elastic Response

Stress belongs to a plane

Stress is force per area at a point, resolved into normal and shear components on a chosen plane. Rotating the plane changes those components even though the underlying state is unchanged. The course uses compression-positive normal stress and an explicit shear convention.

Principal planes are orientations with zero shear stress, and the corresponding normal values are principal stresses.

Mohr's circle transforms the state

The centre of a two-dimensional circle lies at the average normal stress, while its radius depends on the normal-stress difference and shear component. Points on the circle give normal and shear stress on physical planes.

Angular movement on the circle is twice the physical plane rotation. The diagram is valuable because it makes maximum shear and principal states visible, but signs and starting orientation must be set before reading it.

Strain and elasticity describe response

Normal strain is change in length divided by original length. Shear strain describes angular distortion.

Young's modulus is a selected slope of the axial stress-strain relation, and Poisson's ratio compares transverse and axial strains with their opposite directions accounted for. Rock curves can be nonlinear, so tangent, secant or average modulus must be named rather than reported as one context-free value.

In this chapter

What this chapter covers

  • 01

    Stress as force distributed over area

  • 02

    Normal and shear components

  • 03

    Principal planes and stresses

  • 04

    Mohr circle centre, radius and angle

  • 05

    Normal and shear strain

  • 06

    Young's modulus and Poisson's ratio

Worked example · free

Find axial stress and modulus

Q [10 marks]. An eighty millimetre diameter specimen carries three hundred kilonewtons and shortens 0.40 millimetres over a 160 millimetre gauge length. Find stress, strain and secant modulus. The mark allocation used here is an AskSia revision aid, not a University assessment scheme.
The left element shows stresses acting on physical planes, while the circle on the right represents the same state and uses twice the physical rotation angle.The left element shows stresses acting on physical planes, while the circle on the right represents the same state and uses twice the physical rotation angle.A plane orientation changes normal and shear stresschosen planeMohr space doubles the physical angle
The left element shows stresses acting on physical planes, while the circle on the right represents the same state and uses twice the physical rotation angle.
  • 3Calculate circular area with consistent units.
  • 4Calculate axial stress and strain.
  • 3Divide stress by strain and name the slope construction.
Area is π(0.080)²/4 = 0.005027 square metres. Stress is 300,000/0.005027 = 59.7 MPa. Strain magnitude is 0.40/160 = 0.00250. The secant modulus from the origin to this point is 59.7/0.00250 = 23,880 MPa, or 23.9 GPa. The selected portion of the curve must be stated.
Sia tip — Read the modulus unit before accepting the answer. Strain is dimensionless, so the modulus retains stress units.
Glossary

Key terms

Normal Stress
Stress acting perpendicular to a selected plane.
Shear Stress
Stress acting tangentially along a selected plane.
Principal Plane
A plane on which the shear stress component is zero.
Mohr Circle
A graphical transformation of normal and shear stress across plane orientations.
Normal Strain
Change in length divided by original length along a direction.
Poisson's Ratio
The negative ratio of transverse strain to axial strain in a stated range.
FAQ

Stress, Strain and Elastic Response FAQ

Why does stress change when the plane rotates?

The force state at the point is unchanged, but its decomposition into components normal and tangential to the chosen plane changes. Stress transformation expresses that geometry. Principal planes are the special orientations where the tangential component becomes zero.

Why is the angle doubled on Mohr's circle?

The transformation equations contain sine and cosine of twice the physical plane angle. A physical rotation therefore maps to twice that angular movement on the circle. The direction convention must still be applied consistently when locating the transformed point.

Which Young's modulus should be reported?

Use the construction requested or justified by the curve: tangent at a stated stress, secant from the origin to a stated fraction of peak strength, or an average over a selected linear range. Naming the construction is part of the result.

Study strategy

Exam move

For each calculation, draw the plane or specimen and write the sign convention beside it. Practise finding circle centre and radius before transformed stresses. For stress-strain curves, mark the exact two points defining the modulus. End by checking that strain is dimensionless and the modulus has stress units. Separate state, transformation, and material response in your revision notes.

A stress tensor or Mohr circle describes the state at a point; rotating the plane changes the resolved components but not the underlying state. A stress-strain curve describes how a specimen responds under a loading path. Mixing these roles is a common source of formula selection errors.

For transformation problems, write the two normal stresses and shear stress with signs, compute the centre and radius, locate the original faces, and use the double-angle relationship only after the diagram is oriented. Verify principal stresses by confirming zero shear and verify maximum shear by checking the circle radius.

For strain, derive axial and transverse values directly from measured changes and original dimensions before calculating Poisson's ratio. On a nonlinear curve, shade the interval used for a tangent, secant, or average modulus and explain why that choice matters.

Create unit checks that can be done without a calculator: stress and modulus share force-per-area units, strain is dimensionless, and an impossible sign should trigger a review of the convention. Add one interpretation sentence to every numerical answer. State the physical plane, whether the result is compressive or tensile under the adopted convention, and what limitation follows from specimen scale or elastic assumptions.

A final mixed drill should move from a loaded element to Mohr space and then to an expected strain response without treating those diagrams as interchangeable.

A+Everything unlocked
Unlocks this Bible + all 52 of your subjects at The University of Hong Kong, plus 1,000+ more Bibles across the AskSia library.
Sia - your CIVL2102 tutor, unlimited, worked the way the exam marks it
The full 2-page Bible + practice bank with worked solutions
Chrome extension - sync your LMS so Sia knows your deadlines
Bilingual EN / Chinese on every Bible and every Sia answer
$0.99 Trial
30-day money-back · cancel in one tap · how it works