The University of Hong Kong · FACULTY OF ENGINEERING

CIVL2102 Chap.8 Rock Testing and Strength Parameters

- one subject, every graph, every model, every mark
6 Chapters3-page Bible
Our own words - no uploaded lecturer files
Updated for this semester
Chapter 8 of 10 · CIVL2102

Rock Testing and Strength Parameters

Test selection begins with the property question

Index tests provide quick comparative information for classification or correlation. Design tests measure strength or deformability under a controlled stress path. Uniaxial compression supplies peak compressive stress and, with strain measurements, elastic parameters. The Brazilian test infers tensile strength from diametral loading.

Triaxial compression supplies failure states under confinement and supports a strength envelope.

Specimen preparation belongs to the result

Geometry, end flatness, centring, moisture condition and loading rate change the measured response. The uniaxial specimen must be a properly prepared cylinder, and the loading procedure should record load and strain through failure.

The Brazilian disc needs compatible dimensions and a valid central split. A precise calculation from an invalid break should be rejected rather than reported with extra decimal places.

Parameters have domains

Peak load divided by original area gives uniaxial compressive strength. A selected stress-strain slope gives Young's modulus.

Brazilian tensile strength follows from primary failure load, diameter and thickness. Triaxial points define an envelope over the tested confinement range. None automatically represents a jointed rock mass at field scale.

In this chapter

What this chapter covers

  • 01

    Index tests against design tests

  • 02

    Uniaxial compression geometry and loading

  • 03

    Stress-strain and elastic parameters

  • 04

    Brazilian indirect tension

  • 05

    Triaxial confinement and peak states

  • 06

    Failure observation and validity

Worked example · free

Calculate and validate Brazilian strength

Q [9 marks]. A disc is fifty-four millimetres in diameter, twenty-seven millimetres thick and splits centrally at a primary load of twelve kilonewtons. Find tensile strength. The mark allocation used here is an AskSia revision aid, not a University assessment scheme.
The three specimens experience axial compression, diametral compression or axial compression with confinement, so their results answer different strength questiThe three specimens experience axial compression, diametral compression or axial compression with confinement, so their results answer different strength questions.Different load paths recover different strength informationUCSBrazilianTriaxial
The three specimens experience axial compression, diametral compression or axial compression with confinement, so their results answer different strength questions.
  • 3State the indirect-tension relation and units.
  • 3Substitute primary load, diameter and thickness.
  • 3Check the observed failure mode.
Tensile strength is 2P/(πDt). Substitution gives 24,000/[π(54)(27)] = 5.24 newtons per square millimetre, or 5.24 MPa. The central split supports the assumed tensile mechanism. Crushing beneath a loading strip or an off-centre failure would make the calculated value invalid.
Sia tip — A laboratory equation is conditional on the observed break. Validate the mechanism after calculating.
Glossary

Key terms

Index Test
A quick comparative test used for classification or calibrated correlation.
Design Test
A controlled test supplying strength or deformability information for analysis.
UCS
Peak axial stress in an unconfined compression test.
Primary Failure
The first valid specimen failure used for the Brazilian load calculation.
Confining Stress
Lateral compressive stress applied during a triaxial test.
Failure Envelope
A relation fitted to critical stress states across tests.
FAQ

Rock Testing and Strength Parameters FAQ

Why is the observed failure mode important?

The equation assumes a particular stress field and break. End crushing in compression or local crushing in a Brazilian disc indicates another mechanism. Reporting the calculated number would then mislabel what the apparatus actually produced.

What does a triaxial test add beyond UCS?

It measures strength under controlled confinement, allowing several peak states to define a failure envelope. That reveals how strength changes with normal compression and supplies parameters over the tested pressure range rather than at zero confinement only.

Can an index test value be used directly in design?

Only when a suitable correlation has been validated for comparable rock type, weathering state and scale. Index values are useful for comparison and screening, but a handbook conversion does not erase uncertainty or discontinuity effects.

How should conflicting specimen results be reviewed?

Audit dimensions, end preparation, moisture, loading rate, data channels, primary failure load and the observed break before averaging. If unusual values share a defect or failure orientation, the scatter may reveal preparation bias or real fabric. Keep valid material variability visible and reject only results whose test assumptions were not met.

Study strategy

Exam move

For each test, draw the specimen and load arrows, list the controlled quantities, measured responses and validity checks, then write the resulting parameter. Practise one unit conversion in each system. Finish with a sentence separating intact specimen evidence from rock-mass behaviour. Build one test sheet for uniaxial compression, Brazilian tension, and triaxial compression.

On each sheet show specimen geometry, loading direction, controlled variables, instruments, raw readings, equation, expected break, and rejection conditions. Work calculations from newtons and millimetres so that the result emerges in megapascals, then repeat with SI units to verify the conversion.

For a uniaxial test, distinguish peak strength from a modulus taken over a selected stress-strain interval and state whether axial and transverse strains were measured. For a Brazilian disc, inspect whether the primary crack is a central split; loading-point crushing or an off-centre break challenges the tensile interpretation.

For triaxial data, plot several failure states and fit an envelope only over the tested confinement range. Add specimen condition to every result, including dimensions, end preparation, moisture, weathering, orientation, and visible defects. Use repeated specimens to separate laboratory error from genuine material variability rather than averaging incompatible failures automatically.

Practise rejecting a number with a concise mechanical reason; this is stronger than reporting a precise value from an invalid test. Finally, map each intact parameter to the larger ground problem. Ask whether joints, scale, anisotropy, water, or stress path make the laboratory value unsuitable without adjustment.

The closing sentence should identify the property actually measured and the boundary beyond which the result should not be extrapolated.

A+Everything unlocked
Unlocks this Bible + all 52 of your subjects at The University of Hong Kong, plus 1,000+ more Bibles across the AskSia library.
Sia - your CIVL2102 tutor, unlimited, worked the way the exam marks it
The full 3-page Bible + practice bank with worked solutions
Chrome extension - sync your LMS so Sia knows your deadlines
Bilingual EN / Chinese on every Bible and every Sia answer
$0.99 Trial
30-day money-back · cancel in one tap · how it works