The University of Hong Kong · FACULTY OF ENGINEERING

CIVL2102 Chap.7 In-Situ Stress and Measurement

- one subject, every graph, every model, every mark
6 Chapters3-page Bible
Our own words - no uploaded lecturer files
Updated for this semester
Chapter 7 of 10 · CIVL2102

In-Situ Stress and Measurement

The ground carries stress before construction

Natural stress exists before a new excavation. Construction redistributes it into an induced state. The course further distinguishes gravitational, tectonic, residual and thermal origins, together with near-field stress around an opening and far-field stress beyond the disturbed zone.

A measurement can be accurate at its location and still be unsuitable as a far-field boundary condition.

Estimates and measurements play different roles

Overburden provides a first estimate of vertical stress through unit weight and depth. Horizontal stress depends on elastic response and geological history, so a simple proportional assumption may be inadequate after erosion or tectonic loading.

Estimates supply scale checks. Measurements supply site evidence, but only through a method-specific inversion.

Every method observes a response

A flatjack restores deformation caused by cutting a slot at an excavation boundary. Hydraulic fracturing uses borehole pressure at fracture initiation and reopening under orientation assumptions.

Overcoring relieves a sample and measures strain, then converts that strain to stress using elastic properties. The answer should separate what was observed from the assumptions used to infer stress.

In this chapter

What this chapter covers

  • 01

    Natural and induced stress

  • 02

    Gravitational, tectonic and residual origins

  • 03

    Near-field and far-field zones

  • 04

    Vertical overburden estimate

  • 05

    Flatjack and hydraulic fracturing

  • 06

    Overcoring and elastic inversion

Worked example · free

Reject a misplaced boundary condition

Q [9 marks]. Designers need far-field horizontal stresses for a deep tunnel, but the available readings are flatjack results from a nearby cavern wall. Explain the next step. The mark allocation used here is an AskSia revision aid, not a University assessment scheme.
The branches separate a boundary measurement from borehole methods, which infer stress from pressure or strain responses under different access conditions.The branches separate a boundary measurement from borehole methods, which infer stress from pressure or strain responses under different access conditions.Choose a method by access and measured responseAccessible excavation?Flatjack at boundaryBorehole methodfracture pressure or strain relief
The branches separate a boundary measurement from borehole methods, which infer stress from pressure or strain responses under different access conditions.
  • 3Classify the existing measurement zone.
  • 3Choose a method suited to the required components.
  • 3State the assumptions that need verification.
The cavern-wall readings belong to an excavation-disturbed boundary and should not be imported directly as far-field stresses. Boreholes positioned beyond both disturbed zones are needed. Hydraulic fracturing may infer horizontal principal stresses if fracture orientation assumptions hold, while overcoring can recover a fuller state if elastic properties and strain measurements are reliable. Location and assumptions should be set before choosing by cost.
Sia tip — Draw the opening and target point. Near-field and far-field are locations, not labels for measured and assumed values.
Glossary

Key terms

Natural Stress
The in-situ state existing before a new engineering disturbance.
Induced Stress
The redistributed state created by excavation, loading or another engineering action.
Far-Field Stress
Stress beyond the zone materially disturbed by the opening of interest.
Flatjack Test
A boundary method restoring slot deformation with controlled pressure.
Hydraulic Fracturing
A borehole method inferring stress from fracture pressures and orientation.
Overcoring
A relief method inferring stress from measured strains after isolating a core.
FAQ

In-Situ Stress and Measurement FAQ

Why is overburden not enough to define the stress state?

It supplies a useful vertical scale, but horizontal stresses depend on elastic response, tectonics, erosion and locked-in history. Direction and magnitude can therefore differ from a simple gravitational assumption, especially near major structures or excavations.

What does a flatjack test actually measure?

It observes deformation at an excavation boundary after a slot is cut and applies pressure to restore the earlier condition. Stress is inferred from that restoration, so geometry, damage and the disturbed near-field state must be considered.

Why can two stress methods disagree?

They may sample different volumes, locations and discontinuities or use different elastic constants and orientation assumptions. First map those differences and verify fracture or strain directions. Averaging a directional conflict can hide the reason for it.

What should accompany a reported stress result?

Include location, depth, borehole and measurement orientation, the sampled volume, distance from excavations, the observed pressure or strain response, and the assumptions used in inversion. A principal-stress value without this geometry cannot show whether it represents the far field required by the design.

Study strategy

Exam move

Make a three-column method table: disturbance applied, response measured and assumptions used to infer stress. Add the sampled volume and likely excavation influence. For every case, draw near-field and far-field zones. Compare results with an overburden scale check without forcing agreement where geology provides another mechanism.

Start each case by defining the stress quantity the design needs: magnitude, orientation, depth, location, and whether near-field or far-field conditions are relevant. Then test whether the selected method samples that quantity. For a flatjack result, mark the excavation surface and consider stress redistribution.

For hydraulic fracturing, record borehole orientation, fracture orientation, initiation and reopening pressures, and the possibility of reopening a natural discontinuity. For overcoring, trace the chain from stress relief to measured strain to inferred stress and identify where elastic constants enter.

Prepare a comparison table that distinguishes direct observations from inversion assumptions; pressure, strain, and displacement are observed, while a complete stress state is inferred. Use vertical stress from unit weight and depth as a scale check, not as proof that a measured horizontal value is wrong.

Add geological mechanisms such as tectonic loading, erosion, topography, anisotropy, or residual stress when they are supported. Reconcile conflicting measurements by checking orientation, sampled volume, distance from excavations, test validity, and spatial variability before averaging anything.

A useful design drill is to choose a tunnel alignment and state how uncertainty in principal-stress direction would change excavation shape, support, or monitoring. End with a measurement plan that combines methods or locations where one test cannot resolve the required state. The plan should say what disagreement would be meaningful rather than merely seeking repeated numbers.

A+Everything unlocked
Unlocks this Bible + all 52 of your subjects at The University of Hong Kong, plus 1,000+ more Bibles across the AskSia library.
Sia - your CIVL2102 tutor, unlimited, worked the way the exam marks it
The full 3-page Bible + practice bank with worked solutions
Chrome extension - sync your LMS so Sia knows your deadlines
Bilingual EN / Chinese on every Bible and every Sia answer
$0.99 Trial
30-day money-back · cancel in one tap · how it works